Suzuki xl7 which side is bank 2 sensor 2

Question edited for clarity and correct order 'make model 'stuff'.
Question moved to model category.

Passenger side and after the catalytic converter.

https://www.justanswer.com/car/7vwre-getting-code-p0031-2002-suzuki-xl-7-2-7l.html

Oxygen Sensor locations - 2003 Suzuki XL-7

RepairPal.com https://repairpal.com > ... > Suzuki > XL-7 > 2003
Feb 12, 2010 - Driver's side of the engine is bank 1, so passenger side is bank 2, sensor one is engine side of cat converter. Sign in to reply.

where is the low and high side o2 sensor located
Jun 19, 2010
Where is located the knock sensor bank 2 on a 07 Suzuki XL-7
Jun 20, 2018
More results from repairpal.com

..

the cold from hell,,
CAT monitor. know it well, too well.

no its not that.
the code tells that engine has a lazy or dead cat.
no engine stated.
its and XL-7 not and XL7, they are different cars.
3.6L V6
bank one is failing the person who told you bank 2 is full of beans.

"Catalyst Efficiency Below Normal (Bank 1)" SM quote. we change the front B1S1 front sensor first.
then the B1S2, sensor next.
then the CAT if sure no exhaust leaks are on Bank1.
S1 is front
S2 is rear
bank 1, is cylinder 1 side
bank 1 is,, right bank, usa is passenger side

look for leaks first in exhuast
then bad 02s, on right side , damage to wires.
the new sensors.
then new cat, $$$$$$$$$$$$$$$$$$$ last

did you look it up?
alldata.com shows.
it means the engine needs service and inspections here.

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor "B"
Number of Trips to Set Code: 2
Trouble Code Conditions:
Difference between camshaft (bank 1 / exhaust side) position and crankshaft position is out of specified range.
Possible Causes:

• CMP sensor
• CKP sensor
• Signal rotor
• Timing chain
• Timing chain tensioner
• CMP actuator
• ECM

#1 is left side, drivers, or in UK its be passengers. side/.
the word LEFT works on all cars world wide. and is clear.
we drive LHD cars here, but not in UK, or other countries.

the #1 cylinder the most forward cylinder on all v6s
just one glance from top and bingo.
H27engine
or 3.6L>

bolt the H20 to h27a are left side, #1 see photo.

3.6L
. The right bank of cylinders are number 1-3-5 and the left bank of cylinders are 2-4-6. The engine firing order is 1-2-3-4-5-6.

so Bank2 is RIGHT. as is B2s1, front. right.

as clearly seen here, see how #1 sits forward?
we have posted this answer here, like 10 times.
now 11th.

I have the same problem few days ago and found my solution on Fixya Expert Sources website. Here you will get all the top sources of your problem. All the sources of this site provided by top Fixya Gurus. Have a good look at the sources of the page. Go through the sources to find your solution. Hope it will help.


View Count:9

PO-446 EVAP Vent Valve ( Cause of fueling issues & smell)

PO-31 O2 Sensor Bank 1 Sensor 1 ( Bad Heater)

Replace both front O2 Sensors

EGR Valve and or spark plugs (for Jerky)

Itsone one cloest to the front of the vehicle thats how there counted

do not buy the 1 for 69.00 it more or less a universal wher u have to rewire it buy the 1 for 179. and it takes a 7/8 wrench and bank 1 is the 1 on drivers side up by manifold not by converter

You will need a special socket to remove the 02 sensors and a good solvent to spray on the threads to help break them loose. The socket can be purchased at most auto parts stores.

Yes, If you have dual exhaust pipes coming from the engine, Look on the passenger side exhause pipe, and it will be the 1st sensor on the pipe coming out of the engine.