Driver side tire is turned like the wheel is turned but it is not turned

Could be your wheels need to be realigned If your tires are worn will do that also.

Check wheel bearing. Sounds real bad.

The popping could be from a bad CV axle joint, or a bad wheel bearing. Better get checked, sounds very worn. Raise the wheel on a jack and watch for play. Grab wheel at 3 and 9 o'clock, and shake back and forth-watch for play. Wheel bearing? CV joint -is boot still good? Ball joints at bottom of wheel attaching point to the control arm-check this for play, too.

There's something seriously wrong in the transfer case or controls. It seems the rear driveshaft is locked up, and the front wheels are driving. The driver's side rear tire is skidding because it's trying to turn backward - rear passenger rear tire is going forward and rear differential has no option but to turn the driver tire in reverse (driveshaft locked). DON'T TRY TO DRIVE IT. Get it checked out and fixed.

No, even a 4x4 will have only 1 wheel that will spin on each axle in this instance. It's called a floating differential. For stock vehicles with non locking differentials like you have, both cannot spin or have full power at the same time. Hard to explain on this, but picture your car making a hard right turn. Both front wheels would be spinning at different speeds because of the turn. The passenger side tire is spinning much slower than the drivers side tire, therefore if both were spinning at the same time, your tires would chirp and skip on the pavement which would eventually ruin your differential. In offroad applications, we WANT the differentials locked and turning at the same time with true 4x4. But in normal everyday vehicles, even standard stock 4x4's, only 1 tire will do the spinning per axle unless it has possitraction or full locked axle. Clear as snow?

Yes that is normal for a front wheel drive vehicle. The power is applied to the wheel on the passenger side only until a given amount of wheel speed is obtained then the drivers side will spin at the same rate. Although if you raise the front of the vehicle and spin the tires by hand in neutral you should feel equal resistance. If the driver side wheel has excessive resistance to turning the wheel bearing may be to tight..

That could be a broken tie rod end, on the right front wheel.
Or it might be a gear or teeth in the steering mechanism.
Hope this helps.

no just set good sockets and grease and a jack

You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.
The TPMS sensor matching process is outlined below:

1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with the engine off.
3. Press the Remote Keyless Entry (RKE) transmitter's lock and unlock buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.
4. Start with the driver side front tire.
5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position.
6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
11. Put the valve caps back on the valve stems.

TPMS Sensor Matching Procedure

Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool. See your dealer/retailer for service.

The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. If increasing the tire's air pressure, do not exceed the maximum inflation pressure indicated on the tire's sidewall.

To decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage, or a key.

You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.

The TPMS sensor matching process is outlined below:

1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with the engine off.
3. Press the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.
4. Start with the driver side front tire.
5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position.
6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
11. Put the valve caps back on the valve stems.