1998 Jeep Grand Cherokee Logo
Posted on Mar 01, 2010

Code 463 fuel level sensory high imput, what is this and where is it located

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

New Friend:

An expert that has 1 follower.

  • Contributor 40 Answers
  • Posted on Mar 02, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

New Friend:

An expert that has 1 follower.

Joined: Dec 23, 2009
Answers
40
Questions
3
Helped
27214
Points
91

Not sure if this helps or not, but here is information from the 1998 Jeep Grand Cherokee Service Manual, ezg_25.pdf, page 6 of 20…

Hex Code = 95
Generic Scan Tool Code = P0462
DRB Scan Tool Display = Fuel Level Sending Unit Volts Too Low
Description of Diagnostic Trouble Code = Open circuit between PCM and fuel gauge sending unit.

Hex Code = 96
Generic Scan Tool Code = P0463
DRB Scan Tool Display = Fuel Level Sending Unit Volts Too High
Description of Diagnostic Trouble Code = Circuit shorted to voltage between PCM and fuel gauge sending unit.

Hex Code = 97
Generic Scan Tool Code = P0460
DRB Scan Tool Display = Fuel Level Unit No Change Over Miles
Description of Diagnostic Trouble Code = No movement of fuel level sender detected.

for additional information on troubleshooting and resolution:
http://rapidshare.com/files/138412864/ServiceManual.Jeep.Grand.Cherokee.1998_by_Parasico.rar

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Po463 po183 nissan versa

code p 0183 refers to fuel temperature sensor A --high input===causes --wiring short to positive ---fuel temp sensor--ECM
code p 0463 refers to fuel tank level sensor --high input===causes --wiring short to positive fuel tan level sensor ---ECM
if the temp sender and the fuel level sensor ( both located in the same fitting in the tank)are in the same wiring harness then there may be a connection as the wiring short to positive is common
check for the harness rubbed through somewhere causing the problem or an after market screw screwed into the harness some where
0helpful
1answer

My 2000 has codes po171 po300 po 463 po480 what

P0171 =system too lean (bank 1)
P0300 = multiple misfire
P0463 = fuel level sensor circuit high input
P0480 = cooling fan 1 control circuit
0helpful
1answer

P0463 fuel level sensor circuit high

Code 720 is for a problem with the speed sensor in the transmission. The sensor and circuit would need to be checked.
Code 463 is saying the signal from the gas tank sending unit is too high. The sending unit uses a resistor to send a signal back to the computer and the gas gauge. Again, the sending unit and the circuit would need to be checked out.
0helpful
1answer

2000 chevy venture key jammed ignition replaced ignition car wont turn over. OBD-II codes U1000, P0463, P1626. How do I fix problem

Code U1000 is saying the ECM lost communication with the BCM which can happen when the key switch is turned far enough to stop the engine but not enough to turn the accessories off.
Code 463 is for fuel level sensor circuit high which is a problem with the fuel gauge or the sending unit in the tank.

Code 1626 involves the theft deterrent system.
P1626 CHEVROLET - Theft Deterrent Fuel Enable Signal Not Received
Read more: http://engine-codes.com/p1626_chevrolet.html#ixzz210PRFRO9

The code 1626 could be the issue - the passkey system may not be reading the chip in your key.
0helpful
2answers

Po181 p0183 code are on

P 0181 is Fuel Temperature Sensor "A" Circuit Range/Performance, P 0183 is Fuel Temperature Sensor "A" Circut High Imput
0helpful
1answer

Check Engine light comes on and gives a 463 code

This ultimatly will be a problem with your fuel pump. The actual code references the fuel sending unit voltage.. I suspect that your fuel gauge is not operating properly either. The fault is likely with the fuel level sending unit, but on most modern cars its built into the fuel pump.

Good luck.
2helpful
1answer

What is the problem when 463 comes up on the diagnostic code for a 1998 Dodge 1500?

If it's PO463, it should be fuel level sensor circuit showing high input.
4helpful
1answer

2000 chevy truck 1500. I have 3 codes the computer is telling me po404, po405, po463

PO 404 exhaust gas reciculation circuit, range or performance problems
PO 405 exhaust gas reciculation sensor circuit low
PO 463 fuel level sensor circuit high input
0helpful
1answer

Check engine light codes and troubleshooting

Sounds like you have a vacuum leak for the lean code and the misfires. I don't see a 473 code in my manual, but have a 463. The 463 is for the fuel level sensor open or voltage high.
Not finding what you are looking for?

1,248 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...