At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I have a 1998 jeep cherokee limited. where is the the fuse
I have a 1998 jeep cherokee limited. where is the fuse or fuses for the front fog lamps? i know one fuses is under the hood in the engine compartment is there another?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The fog Lamp fuse is located in the interior fuse panel located inside the vehicle to the left of the steering. The fuse your looking for is in the # 24 cavity (Which should be marked by numbers) and it will/should be a 15 amp fuse (lite blue). I hope this helped and good luck.
Fog lamps are installed on the front bumper. The switch is located
to the left of the steering column on the dash panel. The fog lamps are
turned off by the circuit relay when the high beam driving lamps are
turned on. The circuit relay is located on the right front wheelhouse
panel near the blower motor.
Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element See Figure 1
Fig. 1: Exploded view of a fog lamp assembly
Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
Remove the reflector assembly from the lamp body.
Remove the bulb holder from the assembly. Remove the element from the bulb.
DO NOT handle elements with your bare hands, always handle with a
clean cloth. Oil from your hands will cause the element to fail.
Installation is the reverse of removal.
Fog Lamp Switch The fog lamp switch is removed and
installed by simply prying the switch from the instrument panel and
unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT
Position the vehicle on a level surface, facing a wall
approximately 25 feet away. Remove the lamp stone shields and loosen
the adjustment nuts.
Turn the fog lamps ON and adjust as follows:
Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
Install all previously removed items after turning OFF the fog lamps.
If the fuse blows when the switch is off the switch is bad too. If thefuses only blows when the switch is turned on you have a short in thewiring or bulb.
So first, I would removeboth driving bulbs from their sockets and see if there is corrosion.Fix that problem if there is corrosion.
Then install a fuse without the bulbs and see if the fuse blows. If youhave a test light you can bridge the fuse panel without putting a fusein. If there is a connection you have a hot wire grounding. If there isno problem install one light, fuse or bridge the fuse holder and see if1 light works. Try each side. This way you can isolate the problem.Then visibly inspect wiring.
This means you have a short. I am assuming you are talking about the fog light fuse. Does this fuse blow whether the fog lights are off? or just when turned on?
If the fuse blows when the switch is off the switch is bad too. If the fuses only blows when the switch is turned on you have a short in the wiring or bulb.
I don't know if you have test equipment so first I would say to remove both driving bulbs from their sockets and see if there is corrosion. Fix that problem if there is corrosion.
Then install a fuse without the bulbs and see if the fuse blows. If you have a test light you can bridge the fuse panel without putting a fuse in. If there is a connection you have a hot wire grounding. If there is no problem install one light, fuse or bridge the fuse holder and see if 1 light works. Try each side. This way you can isolate the problem. Then visibly inspect wiring.
If you do not have the owners manual showing the fuse locations, then use a 12 volt test light and probe both sides of every fuse to locate the one fuse that has voltage on one side but not the other side of the same fuse.
×