Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

Yes, I can help you with the cylinder head torque wrench setting for your Hyundai Atos 1.0cc. Here are the torque specifications:

First pass: Tighten all bolts to 18 lb-ft (25 Nm)
Second pass: Tighten all bolts to 45 lb-ft (61 Nm)
Third pass: Tighten all bolts to a final torque of 65 lb-ft (88 Nm)
It's important to tighten the bolts in the correct sequence. The sequence is as follows:

10 6 2 3 7
9 5 1 4 8

Note: The numbers above refer to the cylinder head bolts in the correct sequence. Always use a calibrated torque wrench to ensure that the bolts are tightened to the correct specification.

I hope this helps you with your cylinder head installation. If you have any further questions or concerns, feel free to ask.

Install the gasket so that the surface with the identification mark faces toward the cylinder head.
Tighten the bolts to the specified torque in the sequence shown below.

See the settings here:
http://www.autozmagz.com/search/hyundai+getz+cylinder+head+bolt+torque+settings

Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

cylinder head bolt torque

10 mm bolts

step 1 22 ft lbs
step 2 additional 60 degrees
step 3 additional 60 degrees

12 mm bolts

step 1 26 ft lbs.
step 2 additional 60 degrees
step 3 additional 60 degrees

exhaust manifold nut 32-41 ft lbs.

intake manifold nut 11-15 ft lbs.

rocker cover 71-86 in. lbs.

Revised Bulletin
This TSB supersedes the Cylinder Head Bolt Torque Specifications previously described in TSB # 96-20-003, TSB # 96-20-003-1 and TSB # 97-20-004.
DESCRIPTION:
This bulletin provides torque specification corrections to the 1996 and 1997 Elantra Shop Manual, 1997 Elantra Service Data Book, 1997 Tiburon Shop Manual and 1997 Tiburon Service Data Book.
Please record the corrections (listed) in the appropriate manuals and write the TSB number on the bottom of the pages listed below for future reference.
CYLINDER HEAD BOLT:
(M10) 30 Nm (300 kg.cm; 22 lb.ft) + (60°to 65°) + (60°to 65°)
(M12) 35 Nm (350 kg.cm; 26 lb.ft) + (60°to 65°) + (60°to 65°)

The cylinder head bolts need to be torqued at

• 10MM bolts 22 FT-LBS
• 12mm bolts 26 FT-LBS

dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

1st stage 45lbs then 65 then 85