Which one is the tesion pully for a 2004 pacifica i need a diagram

question edited for clarity.
Question moved to model category.

No, it just has the Integrated Power Module in the engine bay.

Chrysler Pacifica (CS; 2004-2008) fuses

Fuse-Box.info https://fuse-box.info > chrysler > chrysler-pacifica-cs-...

In this article, you will find fuse box diagrams of Chrysler Pacifica 2004, 2005, 2006, 2007 and 2008, get information about the location of the fuse panels ...

• 
  

  Fuse Box Diagram Chrysler

  https://fuse-box.info > Home > Chrysler
  Fuse box diagram (location and assignment of electrical fuses) for Chrysler 300 / 300C (Mk1/LX; 2005, 2006, 2007, 2008, 2009, 2010).

Chrysler Pacifica (crossover) (2003-2007) fuse box ...

imgVEHICLE.com https://imgvehicle.com > chrysler > fuse-box

An Integrated Power Module is located in the engine compartment near the battery. This center contains maxi fuses, mini fuses and relays. A label that ...

Chrysler Pacifica 2005 Fuse Box/Block Circuit Breaker ...

CarFuseBox https://www.carfusebox.com > chrysler-pacifica-2005-fu...

Apr 6, 2022 - Chrysler Pacifica 2005 Fuse Box/Block Circuit Breaker Diagram ; 2, C51 18LB/BR, Fused Rear Booster Fan Relay Output ; 3, W4 12BR/OR, Front

..

Here is your fuse box diagram Annie, but the blinkers are not in it, because they are controlled by the Body Control Module. (BCM).

If the front is working okay, check the bulb connections, any wire connectors you can see and the wires in that rear area that go to the body for grounding.

You probably going to need a good auto-electrician.

Fuse Box Diagram Chrysler Pacifica (CS; 2004-2008)

https://fuse-box.info > chrysler > chrysler-pacifica-cs-2...
Fuse box location ... An Integrated Power Module (IPM) is located in the engine compartment near the battery. ... This center contains maxi fuses, mini fuses and ...

• 
  

  Fuse Box Diagram Chrysler

  https://fuse-box.info > Home > Chrysler
  Fuse box diagrams (location and assignment of electrical fuses and relays) Chrysler. ... fuses) for Chrysler Pacifica (CS; 2004, 2005, 2006, 2007, 2008).
  
  ..

You can access the owners manual here. I has all the diagrams and it is free.

Below is a diagram for 3.5L engines. The tension pulley should be the middle left pulley. There should be a tension screw just above it. Loosen the tensioner pulley, route the new belt according to the diagram and while applying pressure to the pulley, tighten it until it's secure.

2004 Dodge Intrepid 3.5L

At Autozone and probably others, the packaging for the belt has the routing diagram on the box.

Click on the following: free, direct Link. It has several Diagrams including the Serpentine Belt Diagram for your 2004 Chysler Pacifica 3.5L DOHC V6. It has the Instructional and Directional Diagrams that will help you.

http://www.2carpros.com/car_repair_information/year/2004/make/chrysler/model/pacifica/2004_chrysler_pacifica_drive_belt_routing_diagram.htm

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench (See Diagram in Link: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Spray some WD-40 on the pully where the belt rests on the pully while the engine is running and the noise will go away, also make sure the belt is tight enough around the pully, if it is loose then tighten it

just above the a/c compressor pully and to the left

Go to your local Napa parts store. If they have updated computers, they can print out your wiring diagram for free.

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2004/make/chrysler/model/pacifica/2004_chrysler_pacifica_drive_belt_routing_diagram.htm