I have to install a new headlight in my 2007 2500hd silverado, do i have to remove the grill in order to install this, and if so how do I remove the grill.

pop hood..there is a star screw about 5 inches long on each side turn it counterclockwise to uninstall the headlight assembly. you may have to remove the grill piece 4 screws then remove turn signal assembly 1 screw on outside edge of van.once headlight assy removed turn headlight 1/4 turn to get to the head lamp bulb. install in reverse order

open the hood - find the 3 or 4 plastic clips that hold on the grill ( the center of the clip will pry up with a small screwdriver ) once the plastic clips are removed pull the grill towards you and gently pull on the headlight frame assembly. The grill will not come off so don't try to force it. Once you have the headlight assembly out remove the bulb that beeds replacing ( when replacing do not touch with bare skin use a rag or paper towel ) Put it all back together reversed from removing it. Hope this helps

To remove old light, remove screws holding the trim around the headlight. Some models require removing the grille to access them. Headlight should pull out and you can detach the plug. Install in reverse order.

How to Replace a Headlight
Parts:
1. Headlight

Tools:
1. Flashlight
2. Screwdriver Set
3. 1/4 in. Drive Ratchet
4. Socket Set

Steps:
Step 1 * Open the hood and locate the headlight.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.

Step 2 * Disconnect the electrical connector from the back of the headlight or remove the headlight bulb.

Step 3 * Remove the headlight from the headlight housing by removing the headlight mounting screws or retainers.
o Tip: Depending on your vehicle, it may be necessary to remove the grille and trim to gain access to the headlight mounting screws.

Step 4 * Compare the new headlight to ensure it will be the correct fit.

Step 5 * Install the new headlight.

Step 6 * Tighten the mounting screws or install the retainers.

Step 7 * If necessary, install the grille or trim that was removed to access the mounting screws.

Step 8 * Install the headlight bulb or connect the wiring harness to the headlight.

Step 9 * Check headlight operation and adjustment. If necessary, adjust the headlight.

Hope helped with this (remember rated this post).

The grille work on these trucks is divided up to three pieces. Right, left, and center.

1. Open hood
2. Remove the two top screws in the corner grille work.
3. Remove the two lower screws in the corner grille work. (these are located right between the bumper and the grille work). Let's just say they are not easy to remove. You would be surprise how many never reinstall these screws.
4. Lift corner grille work away and you will be able to see the screws for the metal frame that surrounds the headlight remove them and replace headlight.
5. Reverse order to install.

it is a very easy diy job. all you have to do is take the grill off by removing the signal lights and taking 5 to 6 screws out of the grill. pull the grill out of the way making sure to unhook the marker light wires. then on your headlight assemblies, unscrew the four 10millimeter screws on each then pull the assy. away and unhook your wires. install is the reverse of removal, its really easy. good luck

Hello streets54, my name is JShreader. Thank you for choosing fixya.com.

First, you have to remove the Upper Radiator Grille. Behind the Headlamp at the top of the Front Bumper, access the lower inside hidden Headlamp Bolt. Only loosen the Bolt. DO NOT REMOVE. Now remove the 2 Headlamp Screws, then the Hidden Screw...now the Headlamp Housing should come out. I uploaded the procedure in .pdf format. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesisitate to ask...Thanks again, JShreader!

The bulb is replaced from the inside,under the hood.Unplug the connector,twist the plastic ring ccw,remove the bulb(make a note of the position of the bulb),install new bulb,twist plastic ring clockwise & plug in the connector.Tip:don't touch the glass bulb with your fingers,the oil from your hands can damage the bulb & shorten the bulbs life.Good luck,
Chev Rev

Hello, the Festiva headlights are very easy to replace, but you have to remove the sidemarker lamps and grill first. That is the trick to the job. I verified the procedure with my Festiva shop manual, so I am sure about it. To remove the side lamp, it has an arm in the upper left that you remove the screw from and then the screws on the outboard side of the side lamp. Once the grill is also removed, you can get to the headlamp holding bolts. Remove those. Then to get the headlamp free from the frame you need to remove the headlamp adjusting screws on the sides. Lastly, remove the wiring from the rear by turning the ring counter-clockwise. That's it. To reinstall the new one, do it in the reverse of the removal procedure. You will probably have to align the headlight beam or at least check it after installing the new headlight. It is adjusted with the headlight adjustment screws that change the angle of the headlight.