- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
THE WINDOW IS OFF THE TRACK.THIS INVOLES REMOVING THE DOOR PANEL TO GET TO THE TRACK . UNLESS YOU ARE VERY MSURE OF WHAT YOU ARE DOING I SUGGEST YOU SEE YOUR REPUTABLE AUTO TECH .THE SPRING ON THE REGULATOR IS UNDER PRESSURE AND IF YOU ARE NOT CAREFUL YOU COULD INJURE YOURSELF. THIS IS NOT A NOVICE REPAIR HOPE THIS HELPS BILL
Remove the little door nob thingy for lock and unlock it just screws off,, Then you have 6 Allen key bolts around the door trim, remove those. Then remove the door handle cover just pops off you may need a small flat blade screw driver. you have two big screws Philips head screws in there... Then remove your speaker cover then the speaker, then remove the speaker, then remove the speaker bracket, then lift the door panel out. The motors and the regulators for your windows are **** door man makes a good unit for them i replace all 4 of mine... They are expensive Partsgeek.com is the best price i could fine. Looked for 2 years in junk yards and posted adds for replacement parts don't wast your time its damn near impossible. cost me about 500 for the 2 front window motors and regulators and I only replaced the regulators on the back windows I think they were about 50 a peace.
door panel pulls straight out or slides, it is held on by plastic mollies they may break when you take it off be very careful not to break them but you can get replacements if needed. check Chevy dealership. there is also one or two screws one at handle, door panel should slide past door handle at angle.
Window Regulator And Motor Assembly REMOVAL & INSTALLATION
Rear Door
Fig. The rear window regulator is an assembly that consists of two pieces
NOTE
The front window regulator is removed as an assembly with the
door control module. Refer to the procedure outlined in this section
under Door Locks.
Remove the door panel and the water deflector.
Remove the door glass (window).
Detach the electrical connector, if equipped, or remove the window regulator handle.
To install:
Install the window regulator.
Place the regulator through the rear access hole into the door.
Attach the electrical connector, if equipped, or install the window regulator handle.
Install the rear side door window.
Replace the door window assembly.
Install the water deflector and the door panel.
Door Locks REMOVAL & INSTALLATION
Door Control Module
Fig. The door control module contains the door locking system module and the power window system module
Raise the window to the full up position.
Remove the inside door trim panel. Refer to procedure outlined in this section.
Pull off the plastic film water deflector enough to access the lock actuator.
Remove the screws securing the door lock actuator.
Remove the door locking system module nuts and bolt.
Remove the door locking system module from the door.
To install:
Installation is the reverse of removal, but make sure to tighten the fasteners to the torque specifications listed:
Door locking system module bolt-89 inch lbs. (10 Nm).
Door locking system module nuts-89 inch lbs. (10 Nm).
for the most part, you will need to remove the door panel, this includes removing the couple of screws in the latch area and the arm rest pull. after this is done, traditionally you will need to remove either 3-4 screws from the bottom of the door panel of a flat blade screw driver or flat pry bar to pop out the panel. after you have removed the items the door panel should be set aside, and carefully remove the plastic lining on the door. locate through the access panel how the window is secured , normally by screws or bolts or by a locking clip. remove these and remove the window. there are usually three bolts around the regulator, remove them, in addition, there are 2 bolts on each side of the window tracks, remove these, you will need to twist out to remove, replace your new regulator and re assemble as you have taken apart, this is normally a 3-4 hour time period to replace, Good Luck!!!
probably need a new window regulator. ebay. 93 to 98 should fit.
Section 01-05: Trim, Interior
1998 Villager Workshop Manual
REMOVAL AND INSTALLATION
Trim Panel(s), Door
Front Removal
Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
Pull the shop rag back and forth to release the window regulator handle clip.
Remove the three cover caps and front door trim panel screws.
Remove the one front door trim panel capped screws from the door pull handle.
If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power
Front Door Removal
Disconnect the battery ground cable (14301) .
Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
Remove the two front door brace bolts and the front door brace.
Disconnect the front window regulator electric drive electrical connector.
Remove the four front door window glass regulator track bolts.
Remove the three front window regulator electric drive bolts.
Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
I just replaced the regulator in my mother's 98 civic ex and didnt need any special tools. I do recommend replacing the glass run channels on either side of the window. I have replaced the regulator twice and it is still having problems as I haven't replaced the run channels. If not replaced very soon I can see myself replacing the regulator...yet again!
×