Can water pump be removed and re-installed W/O removing any pulleys on a 1988 Samari Suzuki.

this is in the fsm.
read it
here it is .
http://www.fixkick.com/sammi-stuff/index.html

I'm assuming you know how the shift works.......sometimes it is a little difficult to position the lever correctly. Due to a possible problem with the plastic "cup" that supports the shift lever, you will need to remove the shift lever from the transfer case, and Use a big screw driver to move the mechanism to the neutral position. Many Samurai suppliers offer the kit to fix the shift

Because of many things involved,. you need to go to your local parts store and get a Haynes or Clymer manual

1. Remove air filter to give you more room to play
2. Loosen alternator and alternator tensioner. Alternator tensioner bolts to water pump so that bolt will need to come out.
3. With the alternator loose, the main drive belt should be loose and be able to be removed, do this.
4. Loosen the tensioner bolt for the air conditioner, on the underside of the engine. Losen the nut on the air conditioner tension wheel. The tensioner wheel should now slide up and down freely, allowing removal of the air conditioner belt.
5. Remove the 4 x 10mm bolts on the water pump pulley. Remove the water pump pulley.
   
6. Remove the 4 x 10mm bolts on the camshaft pulley. This is the main pulley that all the belts connect to. There is a large 17mm bolt in the middle of this pulley that does not need to be removed. (Crankshaft Bolt).
7. The camshaft pulley should slide off, however you will probably have no clearance (because of the crankshaft bolt) to remove the pulley. The pulley has to be removed.
   
8. Place a jack under the sump, use a piece of wood to protect the sump. Jack the sump up 1/2 inch. Undo the two 14mm bolts in the engine mounts. When the two left hand engine mount bolts are out, lower the jack slowly until you can slide the camshaft pulley out.
   
9. Remove the plastic timing belt cover.
10. You should now see the timing belt, remove the timing belt tensioner pulley, being careful not to move the timing belt wheels.
11. Undo the bolts holding the water pump.
12. Water pump should come off, water will come out if you haven't drained it.
13. Scrape off gasket.
14. Install new water pump.
15. Reassemble in reverse order.

Read more: http://wiki.answers.com/Q/How_do_you_replace_a_water_pump_on_a_1991_Suzuki_Swift#ixzz1BIA5PNWR

It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
Removal Procedure :

1. Drain the cooling system until the coolant is below the level of the water pump.
2. Remove the drive belt guard.
3. Loosen the water pump pulley bolts.
4. Remove the drive belt.

1. Remove the water pump pulley bolts.
2. Remove the water pump pulley.

1. Remove the water pump bolts.
2. Remove the water pump.
3. Remove the water pump gasket.
4. Clean the water pump mating surfaces

Installation Procedure

1. Install the water pump gasket.
2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
3. Install the water pump bolts.

• Tighten the bolts to 10 Nm (89 inch lbs.) .

1. Install the water pump pulley. Loosely install the mounting bolts.
2. Install the drive belt.
3. Install the water pump pulley bolts.

• Tighten the bolts to 25 Nm (18 inch lbs.) .

1. Install the drive belt guard.
2. Fill the cooling system.
3. Inspect the cooling system for leaks.
4. That's it.

1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system

1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system
Visit my Blog here

need special tool to pull calls power steering puller

Notes Water Pump Replacement

Removal Procedure

1. Drain the cooling system until the coolant is below the level of the water pump.
2. Remove the drive belt guard.
3. Loosen the water pump pulley bolts.
4. Remove the drive belt.

1. Remove the water pump pulley bolts.
2. Remove the water pump pulley.

1. Remove the water pump bolts.
2. Remove the water pump.
3. Remove the water pump gasket.
4. Clean the water pump mating surfaces

Installation Procedure

1. Install the water pump gasket.
2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
3. Install the water pump bolts.

• Tighten the bolts to 10 Nm (89 inch lbs.) .

1. Install the water pump pulley. Loosely install the mounting bolts.
2. Install the drive belt.
3. Install the water pump pulley bolts.

• Tighten the bolts to 25 Nm (18 inch lbs.) .
• 

1. Install the drive belt guard.
2. Fill the cooling system.
3. Inspect the cooling system for leaks

1. Remove the negative battery cable.
2. Drain the engine cooling system.
3. Remove the air cleaner assembly.
4. Remove the A/C compressor suction pipe bracket (if equipped).
5. Loosen four water pump pulley bolts. Do not remove the bolts.
6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
7. Remove the right lower splash shield.
8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
10. Remove the crankshaft pulley.
11. Remove the water pump pulley (four bolts).
12. Remove the timing belt.
13. Remove the oil level indicator (dipstick) guide tube.
14. Remove the upper generator adjusting bracket from the water pump (one bolt).
    
    
    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
    • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
    1. Install the oil level indicator (dipstick) guide tube.
    2. Install the timing belt.
    3. Install the water pump pulley.
    4. Finger-tighten the four bolts.
    5. Install the crankshaft pulley.
    6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.