How to remove windshield wiper arms of dodge B250

I don't know if your trying to get the wiper arm off or just the refill? If your trying to wiper arm off, there usually a small clip that you pry out to remove arm.
If you just talking about refill blade, I don't know w/o looking at it? Your local auto store might replace the refill blade for you, where applicable?

take of the little panel under wind sheild youll see the mechanism remove bolts on wiper areas after you remove the wipers then get 2 packets of conectors from auto shop few bucks for 2 you need 4 lubricate and use a large socket and a mallet to seat the plastic conectors then replace the mechanism !! sounds difficult but its pretty easy if it doesn't work you need to recheck which way the bars are I messed it up once and it didnt work replaced the plastic conectors other way round reinstalled and done it worked

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?fromSearchPage=true&pageId=0900c1528003c621&partName=Windshield+Wiper+Motor&partId=0900c1528003c621,Click on link deecah2 and you will see how to do it.

IF YOU HAVE A PLASTIC CAP ON ARM REMOVE IT AND THE NUT UNDER IT, AND LIFT WIPER ARM OFF.

Remove Wiper Arms,Metal Grill, Nut on Motor Arm,3 Bolts holding wiper motor.
Dealer has a reman. About $59.00
Remove mounting plate from yours. 3 bolts,turn in old core at dealer

Windshield Wiper Motor
Removal & Installation
To Remove:

1. Remove wiper arms.
   
2. Remove weatherstrip from cowl.
   
3. Remove two cowl vent grille panel screws.
   
4. Remove windshield nozzles and hoses.
   
5. Remove three cowl vent grille panels.
   
6. Disconnect windshield wiper motor electrical connector.
   NOTE: Do not remove crank arm from windshield wiper motor.
   
   
7. Loosen nuts that attach the drive link brackets to the crank arm.
   
8. Remove wiper motor crank arm brackets.
   
   
   
   
   
   
   
   
   
   
   
9. Remove three bolts and windshield wiper motor from vehicle.

To Install:

1. Install windshield wiper motor and three bolts.
   
   
   
   • Torque to: 62 in lbs. (7 Nm)
   
   
2. With right side linkage closest to the windshield wiper motor, install drive
   link brackets to wiper motor crank arm.
   
   
   
   • Torque nuts to: 44 in lbs. (5 Nm)
   
   
3. Connect electrical connector.
   
4. Install nozzles and windshield washer hoses to cowl vent grille.
   
5. Install three cowl vent grille panels and screws to vehicle.
   
6. Install weatherstrip to cowl.
   
7. Install wiper arms.

why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.

1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.

1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.

1. Remove left windshield wiper adapter and connecting arm clip access cover.

1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
   

----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal

1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.

1. Disconnect battery and wiper motor electrical connector.

1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .

1. Disconnect the battery ground cable (14301).

1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .

1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.

1. Reach through the access cover opening and unsnap the wiper motor clip.

1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.

1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.

1. Remove nut and ground strap.

1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .

Installation

1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).

1. Install nut and ground strap.

1. Connect wiper motor electrical connector.

1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.

1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.

1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.

1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
   

1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.

1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.

1. Test the system.

remove wiper arms and then you can raise the hood to remove screws that hold down the vent panel.
now carefully remove vent panel.

SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal

1. Disconnect the battery ground cable (14301).

1. Remove the windshield wiper pivot arms (17527).
   1. Remove the nuts (one each side).
   1. Remove the windshield wiper pivot arms.

1. Remove the LH and RH cowl top vent panels.
   1. Remove the hood weatherstrip.
   1. Remove the screws.
   1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.

1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
   1. Remove the nuts.
   1. Remove the bolt.
   1. Position the windshield wiper mounting arm and pivot shaft assembly aside.

1. Remove the windshield wiper mounting arm and pivot shaft assembly.
   1. Disconnect the electrical connector.
   1. Remove the windshield wiper mounting arm and pivot shaft assembly.

----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal

1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .

1. Remove the windshield wiper motor (17508).
   1. Remove the output shaft bolt.
   1. Remove the bolts.
   1. Remove the windshield wiper motor.

There is a little hook like metal piece under your windshield wiper arm.When you push it to the right while pulling the wiper arm up it comes off