Dodge ram 1500 2001 codes coming up 0753 1757 1762 1765 trans not shifting proper trans in drive wont shift to lower gears automaticly

Sounds like the trans could use a service, it might be too late to save it and will need a rebuild, but your description sounds like low pump pressure.

Dodge Neon Questions - 04 neon will not go into high gear ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusNov 3, 2012 - 04 neon will not go into high gear - 04 neon won't go into high gear. changed transmission fluid. (it tried to change after fluid was changed) gas cap ... ... Car: 2003 Dodge Neon SXT, automatic transmission. As of today, I have ...

Dodge Neon Questions - 2005 Dodge neon does not shift ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusApr 6, 2014 - Your cars computer gathers info on speed in order to shift gears properly.... then you won't have a speedo and the ECM will not tell the TCM to shift gears in the trans. .... Car: 2003 Dodge Neon SXT, automatic transmission.

Neon wont shift out of first gear auto. - DodgeTalk : Dodge Car ...

www.dodgetalk.com > ... > Dodge Neon - General Talk

Jul 30, 2011 - I have a 2003 dodge neon se and it will run and drive. The transmissonwill not shift out of first gear. Where do I start? Compare to Toyota Tundra. Get Tundra on ... 2000 Stratus won't shift out of First Gear
Mar 14, 2007
Not shifting out of Second Gear???
Jan 15, 2007
46RE wont shift out of first at full throttle.
Nov 17, 2006
Transmission wont shift
Nov 3, 2005
More results from www.dodgetalk.com

lock up torque converter is toast. I had the exact same problem in my 2003 2500.

any codes in diagnostics? was pump checked for proper pressure?

1999 dodge 1500 5.2 will not shift to second once the engine reaches normal temperture or I shift from drive to nutural and back to drive then it will work fine untill the next time I stop. filter, fluid, shift slenoid,governor sensor have been replaced.

the computer is not reading the wheel speed/throttle position properly. in this case there should be codes stored on the computer in the trans which might tell you why it wont shift properly. Take it to autozone and get them to scan codes from the computer, then come back and let us know if there are any.

There are many things to consider with an automatic. Check that you have installed the kick down cable and spring correctly. If the kickdown is stuck or the spring is holding it in the wrong direction this will cause your problem. Insure your 8 pin plug is seated properly into into the sillinoid connector. Also check and see if any transmission codes have been set. Hope this helps.

Find your throttle valve cable attached up near cable from throttle pedal ,it's the one that runs down behind toward transmission. With engine off in park,park brake on, Have someone push gas pedal to the floor & observe that cable, to make sure it is retracting properly when pedal released. Now get under & watch where that cable attaches & watch it while doing the same with gas pedal. The lever that it attaches to should move freely & rotate one way when gas pedal pushed, and should return all the way the other way when pedal released. Sometimes that linkage or cable will get seized, and not return fully, which will hold transmission in lower gear. You can use your hand to make sure it is returning all the way if necessary, and if needed, apply penetrating spray to loosen it up, then apply something like white lithium grease to coat it after it's unseized, to prevent repeat in near future.

did you check your transaxle fluid level? drain/replace transaxle fluid dont forget the friction modifier additive. it is required for proper function of your limited slip. signs of a failing differential are metal shavings in the bottom of the case, worn ring/pinion grooves. the other issue with your shift problem could be a failing shift solenoid, however, a vacuum leak will cause crappy shifts because your trans relies on good vacuum to shift.

ummm i would say you need to adjust your trans shift cable, check your fluid level, and the problem i had with my dodge was similar to yours... it was my 3rd-4th actuator spring, it had broke and couldnt hold the pressure to keep it in gear