How do i fix emission codes p1131 p1151 p0171

P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2


p1131 p1151 p0171 p0174 p1131 p1151 p0171 p0174
All of these p1131 p1151 p0171 p0174 codes indicate a problem with a lean condition. This engine is known for vacuum leaks, so before you start throwing oxygen sensors at the problem, it pays to perform some diagnostics.
Start by cleaning the MAF sensor. Spray the sensor with CRC MAF sensor cleaner. Next, check the plastic vacuum lines, especially where they meet with rubber boots. If they are cracked or the rubber is swollen, replace the line. Then check the rubber elbow that holds the PCV valve. That elbow is a know failure point. In fact, the entire PCV tubing is a trouble spot on these engines. (thanks Ford).
After you've checked for vacuum leaks, check the operation of the oxygen sensors. The easiest way to do that is to disconnect the sensor from the harness. Connect one lead of your digital voltmeter to the black wire on the sensor and the other lead to battery negative. Then start the engine and add fuel (either propane, starting fluid, or carb cleaner) into the throttle body to force the mixture to rich. You should see a corresponding increase in voltage as you add fuel (from 0 volts to slightly less than 1 volt). Start and stop the fuel enrichment and watch the meter to see if the volts drop as you stop adding fuel. If you see no change, the sensor is dead. Replace it.
You can also use the fuel enrichment procedure to locate intake gasket leaks.
P1131 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 1
P1151P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2
P0174 system lean bank 2
P0171 system lean bank 1


This is the only info that didn't come back directly to FORD (yet still mentions it) instead of GM. Not to sure you got the correct code.

I don't care how handy you are , that's not going to help you unless you have knowledge of OBD 2 engine management system for your vehicle . Plus having diagnostic test equipment , scan tool to view engine sensor data ., an knowing how to do automotive electrical circuit testing.
Po171 Could be just an O2 sensor problem ,looking at scan data for bank 1 sensor 1 for proper switching , could be a easy find for a trained Tech . You on the other hand could spend hundreds an still not fix the problem .

P0171 - System to Lean (Bank 1) The Adaptive Fuel Strategy continuously monitors fuel delivery hardware. The test fails when the adaptive fuel tables reach a rich calibrated limit. For lean and rich DTCs:

• Fuel system
• Excessive fuel pressure.
• Leaking/contaminated fuel injectors.
• Leaking fuel pressure regulator.
• Low fuel pressure or running out of fuel.
• Vapor recovery system.
• Induction system:
  • Air leaks after the MAF.
  • Vacuum Leaks.
  • PCV system.
  • Improperly seated engine oil dipstick.
• EGR system:
  • Leaking gasket.
  • Stuck EGR valve.
  • Leaking diaphragm or EVR.
• Base Engine:
  • Oil overfill.
  • Cam timing.
  • Cylinder compression.
  • Exhaust leaks before or near the HO2Ss.

P1130 - Lack of HO2S-11 Switch, Fuel Trim at Limit The HEGO Sensor is monitored for switching. The test fails when the HO2S fails to switch due to circuit or fuel at or exceeding a calibrated limit.

• Electrical:
  • Short to VPWR in harness or HO2S
  • Water in harness connector
  • Open/Shorted HO2S circuit
  • Corrosion or poor mating terminals and wiring
  • Damaged HO2S
  • Damaged PCM
• Fuel System:
  • Excessive fuel pressure
  • Leaking/contaminated fuel injectors
  • Leaking fuel pressure regulator
  • Low fuel pressure or running out of fuel
  • Vapor recovery system
• Induction System:
  • Air leaks after the MAF
  • Vacuum Leaks
  • PCV system
  • Improperly seated engine oil dipstick
• EGR System:
  • Leaking gasket
  • Stuck EGR valve
  • Leaking diaphragm or EVR
• Base Engine:
  • Oil overfill
  • Cam timing
  • Cylinder compression
  • Exhaust leaks before or near the HO2S(s)

A fuel control HO2S PID switching across 0.45 volt from 0.2 to 0.9 volt indicates a normal switching HO2S. P1131 - Lack of HO2S-11 Switch, Sensor Indicates Lean A HEGO sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time. See Possible Causes for DTC P1130
P1151 - Lack of HO2S-21 Switch, Sensor Indicates Lean A HEGO sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when fuel control system no longer detects switching for a calibrated amount of time. See Possible Causes for DTC P1130 006 O2 Sensor Signal Analysis

Autozone and some other auto part stores will scan for free and tell you what all the codes are/mean.

All these are fuel trim codes and fuel control O2 sensor related codes, you have something that is causing this as all the sensors seldom fail. My advice here is to see a Ford dealer for the diagnostics before any parts are replaced.

you can look it up on "obdii" trouble codes web site

P1131 Lack of HO2S-11 Switch ,Sensor Lean
P1151-Lack of HO2S-21 Switch ,Sensor Lean
PO171- System to Lean (Bank 1)
PO174-Systen to Lean (Bank 2)

Fuel Filter -Plugged
Low Fuel Pressure
Evap System -Leaks
Leaks - in ducting,air filter to throttle
PCV -Leaks
Exhaust System -Leaks
O2 Sensors-worn out

Hi, 1151 is an 02 sensor code, 1131 is also 02 sensor code,
0174 lean condition bank 2, and 0171 is lean bank 1. Either this is in need of a whosale of repairs or you have computer issues, From looking at the codes i would first do a complete tune up, Including wires, And inspect for a vacume leak before replacing any 02 sensors..
Take care

Change plugs, and Mass Air Flow sensor. This should do the trick

it could but most likely not check for a vacuum leak check the hoses to the throttlebody the rubber fittings have a tendancy to get soft and collapse

po301 thru po306 all misfire codes cylinder 1-6 remove plugs and replace them..... set the plug gap first
i suggest u replace the wires also if they never been replaced all these misfire codes can set the others and one is for the oxygen sensor ( 02s or HO2S) CIRCUT MALFUNCTION do u know how to check wireing systems
do the tune up plugs (set gap) .052-.056 change the fuel filter also. clear the codes hows it run
this info is for 98 E-250 4.2Litre
what engine do u have 4.2L or 4.6L i know it is a v-6 by the codes