My 2002 2500HD 4x4 front axle not engaging

The reason the light is flashing constantly is because the vehicle is sensing that four wheel drive(4WD) is not working. These 4WD systems use vacuum from the engine to engage/disengage to front axle. The vehicle probably has no vacuum going to the front axle, which would not allow the 4WD shift to complete, which would then leave the light on the dash flashing.
First thing to check is that the vacuum actuator on the firewall is working as it should.

Which of these does your vehicle have ?

Transfer Case - NVG 233-NP1 (Two Speed Selectable)
Transfer Case - NVG 136-NP4(One Speed Automatic)

The New Venture Gear NV233 is an electronic shift transfer, with the following three modes of operation, Two-wheel drive high range, Four-wheel drive high range, Four-wheel drive low range. The gear reduction for low range is provided by a planetary gear set. The floor-mounted shifter has been eliminated. A switch, located on the upper right side of the instrument panel, is used to select the operating range. The indicator lamps on the switch show the current mode of operation. When the four-wheel drive has been selected, the four-wheel drive indicator lamp on the switch is designed to turn on when the front axle has engaged.


Automatic Transfer Case
The single speed automatic transfer case system shifts automatically from rear wheel drive to four wheel drive when the transfer case shift control module (TCSCM) senses the difference in rotation speed of the front propeller shaft and the rear propeller shaft . Two vehicle speed sensors, one located at the rear output shaft area of the transfer case, and the other, located at the front output shaft area of the transfer case, send front and rear propeller shaft rotation speed information to the TCSCM.
When the front and rear output shaft rotations remain the same, the TCSCM sends pulse width modulation signals to the encoder/motor to keep the transfer case in rear wheel drive. When the front and rear output shafts rotations are different, the shift control module sends pulse width modulation signals to the encoder/motor to engage the transfer case into four wheel drive.
The system will automatically transfer a percentage of torque to either the front or rear axles as required to stop all wheel slip. When the front and rear output shafts rotations return to the same speed rotation, the shift control module sends pulse width modulation signals to the encoder/motor to position the transfer case back into rear wheel drive.
When the transfer case is engaged into four wheel drive, a lamp indicator on the instrument cluster will light. The automatic transfer case system is completely automated, no transfer case control button switching system is required.

Do you know what diagnostic trouble code's are ?

DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error
DTC C0895 Device Voltage Malfunction

Not OBD2 engine code's .

Your vehicle had option of two different 4x4 systems ,
New Venture Gear 263 Selectable Two Speed Transfer Case
The NVG 263 transfer case features a three button shift control switch located on the instrument panel. When the vehicle has the ignition key in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp will continue to flash until all shifting criteria has been met and the new mode/gear position has been reached (or has been engaged). Once the new mode/gear position is fully active, the switch indicator lamp for the new position will remain ON constantly.
The NVG 263 transfer case provides the driver with 3 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
OR
The NVG 236/246 transfer case features a 4 button shift control switch located on the instrument panel. When the vehicle has the ignition key in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp will continue to flash until all shifting criteria has been met and the new mode/gear position has been reached, or has been engaged. Once the new mode/gear position is fully active, the switch indicator lamp for the new position will remain ON constantly.
If there are problems with electronic part of the systems the shift control switch light will flash warning of a problem , If no lights you have a mechanical problem in the transfer case itself .
The front axle control circuit consists of an electric motor actuator which engages and disengages the front axle. The front axle actuator motor consists of a Permanent Magnetic (PM) motor, a worm gear controlled plunger, a front axle switch and an electronic control circuit all within the actuator assembly.
The front axle actuator has four circuits connected to it, a front axle feed circuit, front axle ground circuit, front axle control circuit and a front axle switch circuit.
Whenever a shift to AUTO 4WD, 4HI, or 4LO is requested, the transfer case shift control module engages the front axle by grounding the front axle control circuit through a current limiting driver. Test Description
The numbers below refer to the step numbers on the diagnostic table.
Tests the electrical function of the front axle actuator. Helps determine between mechanical and electrical malfunctions.
Tests for proper power and ground at the front axle actuator.
Tests the operation of the front axle control circuit.
Helps determine if the transfer case shift control module is able to monitor the front axle switch.
Tests the front axle switch circuit for an open or high resistance.
Measures the voltage between the front axle feed circuit and ground.
Tests the front axle control circuit for an open or high resistance.
Inspects the front axle for a mechanical malfunction.
Tests for open in the front axle feed circuit.

Which do you have ?
Transfer Case - NVG 236 (Two Speed Automatic)
Transfer Case - NVG 233-NP1 (Two Speed Selectable)
The NV236 transfer case is an automatic transfer case with three drive ranges. Shifting from rear wheel drive to four wheel drive is done automatically when the transfer case shift control module receives wheel rotating slip information from the speed sensors. The transfer case shift control module then engages the transfer case motor/encoder to position the transfer case from rear to four wheel drive. When the transfer case shift control module receives information that the wheel rotation is the same on both axles, the transfer case shift control module sends position information to the motor/encoder to put the transfer case back into rear wheel drive. The three drive ranges are 2HI, 4HI, and 4LO. The 2HI position is for normal driving with the rear wheels pushing the vehicle. The 4HI, position is for driving through sand, snow, mud, gravel, or heavy rain at normal or slightly below normal speeds. The 4HI engages the front axle to allow for four wheel drive. The front axle is pulling the vehicle, and the rear axle is pushing the vehicle. The 4LO range is used for off road driving, heavy snow, deep mud, or shallow fording. The 4LO is similar to the 4HI except that the gearing in the transfer case is set for low speed and high torque. The NV236 is manufactured at Syracuse New York by New Venture Gear a division of New Process Gear for General Motors.
Is the switch light on or flashing ? If you have automatic 4x4 there are several DTC'S that can set >
DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0362 4LO Discrete Output Circuit High DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error

The Selectable Four Wheel Drive (S4WD) Front Axle consist of the following components:
• Differential Carrier Housing
• Differential Case Assembly
• Inner Axle Shaft
• Intermediate Shaft Bearing Assembly (located on the right side of the oil pan)
• Electric Motor Actuator
The front axle on Selectable Four Wheel Drive (S4WD) model vehicles uses a disconnect feature mounted on the right side of the oil pan in order to engage and disengage the front axle. When the driver engages the 4WD system, the Transfer Case Control Module sends a signal to the electric motor actuator to energize and extend the plunger inside. The extended plunger moves the clutch fork and clutch fork sleeve across from the clutch fork outer gear that is splined to the right side wheel drive shaft to the clutch fork inner gear that is splined to the inner axle shaft. The locking of the two gears allows the axle to operate in the same manner as a semi-floating rear axle. A propeller shaft connects the transfer case to the front axle. The differential carrier assembly uses a conventional ring and pinion gear set to transmit the driving force of the engine to the wheels. The open differential allows the wheels to turn at different rates of speed while the axle continues to transmit the driving force. This prevents tire scuffing when going around corners and premature wear on internal axle parts. The ring and pinion set and the differential are contained within the carrier. The axle identification number is located on top of the differential carrier assembly or on a label on the bottom of the right half of differential carrier assembly. The wheel drive shafts are completely flexible assemblies consisting of inner and outer constant velocity CV joints protected by thermoplastic boots and connected by a wheel drive shaft.

How To Install Repair Replace 4x4 Front Axle Actuator Chevy Trailblazer...

my computer problem is hard disk system found warantty hard disk

the front axles have pinon gear box that the shaft from the transfer case goes to, it has a vacuum hose to it or a solenoid actuator check these for proper function this is how the power is turned on to the wheels.

Sounds like the chain in the transfer case has broke or the linkage is out of adjustment

There are two parts to the 4X4 engagement. One part is the transfer case actually shifting into four wheel, and the second part is the front axle engaging.
If you have a manual shift, as long as the linkage is working, the transfer case is engaged and the problem will be in the front axle. If you have an electronic shift, you can determine if the transfer case is engaged by the lights on the switch. If the switch lighting is correct, the problem is in the front axle. If the lights are not correct, reset the encoder motor module (located behind the ash tray, listen for the clicking when you press the 4X4 button) by disconnecting it for a few seconds and reconnecting it. If this doesn't correct the problem, it's probably the encoder motor. (located on the driver's side of the transfer case) After you change the encoder motor you may have to reset the module again.

Front axle-verify the servo (either air or electric) is operating the clutch fork in the axle by removing the cable end in the axle. Sometimes it's a small shear spring that breaks. Otherwise, usually it's the shim kit and/or fork that need to be replaced. Parts are cheap, but it takes some time because you have a lot of parts to remove.

Theres a vacume dash pot under the battery box. It pulls a cable that engages the front diff. Put the vacume line and you'll have lights and four wheel drive. (it happened to my blazzer)