Question about 1997 Hyundai Accent

1 Answer

My airbag light won't turn off?

Hi I replaced an engine starter on my wife's Hyundai accent
and after I did the airbag light wont't turn off, the car starts
drives and my wife is worried the airbag might deploy
can some one tell me something else that can be done to fix
the problem.
it's a 1997 hyundai Accent gl 1.5 engine, automatic trans.

thanks.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 49 Answers

When the airbag light is on it is disabled.
a scan tool can read the codes that are turning the light on,
a common problem is clockspring in the column.

Posted on Mar 03, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1665 Answers

SOURCE: installing new brake pads on 2000 hyundai Accent GL

REMOVAL 8118049.gif 1. Remove the lower bolt and lift the caliper assembly up and secure it with a wire or some other retaining method. 2. Remove the pads. CAUTION: Do not depress the brake pedal while disassembling the pads 30c09b4.gif

INSPECTION 1. Check the pads for wear or oil contamination and replace, if necessary. caution_icon.gif The pads for the right and left wheels should be replaced at the same time. Never "drop" or intermix brake pad sets. All four pads must be replaced as a complete set. When replacing the brake pad, check for deformation. When replacing the guide spring, use a new one or the used one after cleaning away foreign material. 2. Check the pad for damage or deformation. Brake pad thickness: Standard value: 9 mm (0.354 in.) Service limited value: 2 mm (0.0787 in.)21873bf.gif
INSTALLATION 1. Install the pad clips. 2. Install the pads onto each pad clip.
3. Insert the piston in the cylinder using the Special Tool (09581-11000).b3dcdee.gif 4. Install the new pads. The shims are attached to each pad as illustrated5efc485.gif caution_icon.gif Be careful so that the disc or pad isn't contaminated by grease. 5. Install the bolt and tighten to the specified value. Tightening torque Guide rod bolt: 22~32 Nm(220~320 kgf·cm, 16~24 lb·ft)

Posted on Jun 11, 2008

SOURCE: 2000 Hyundai Accent GL check engine

i just replaced the timing belt, and asked the garage to look at the transmission for me because i thought i was experiencing some subtle shifting problems. they told me the transmission looked fine, but i needed a new filter and fluid. the engine light didnt turn on til a couple weeks later tho. does this sound like a new filter and fluid would fix this problem?

Posted on Sep 09, 2008

  • 1 Answer

SOURCE: how do you remove radio from hyundai accent 1998

You have to take out the ash tray, and remove those two screws, then pop out the center dash trim. Careful, though, you have to take out a lot of the wiring inside of your center dash trim in order to pull it out for enough room to move the radio in and out. I'm doing this right now, actually..

Posted on May 22, 2009

  • 69 Answers

SOURCE: changing timing belt on 2004 hyundai accent

Sign up for an account on hmaservice.com. Once you do so, log in and click on "Shop". You can then enter your year/make/model and you will find the info under, engine mech. system>timing system>timing belt>repair procedures. Very detailed, and best of all, FREE.

Posted on May 27, 2009

  • 1986 Answers

SOURCE: Replacing bulb (Headlight) in 2000 accent GL

once you pop the hood, there should be a cover behind the light housing that you twist to open the backing.. inside the housing will be a spring lever that secures the bulb down... unhook the spring and disconnect the harness connecting to the bulb...

Posted on Sep 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 hyundai elantra will not go in reverse...any ideas?


Hyundai Elantra transmission won t go into reverse m ...

www.fixya.com > ... > Cars & Trucks > Hyundai
Hyundai Elantra cars & trucks transmission won t go into reverse m ... Question about 1998 Elantra. 1 Answer · Reverse gear almost dead in 1998 Lantra auto.

99 accent wont go into reverse - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/...accent/157948-99-accent-wont-go-into-rev...

Mar 28, 2013 - 3 posts - ‎3 authors
Here is my situation and am hoping I might get somebody who can actually help me with this. I have a 99 hyundai accent automatic with ... 2001 Accent No Reverse
10 posts
Apr 10, 2011
1998 Hyundai Accent Automatic Trans Problem ...
10 posts
Dec 6, 2005
More results from www.hyundai-forums.com

Why is it having trouble moving in reverse?


Jan 05, 2016 | Hyundai Cars & Trucks

1 Answer

Hyundai accent 2000


starter is no good try replacing the starter

Jan 18, 2014 | Cars & Trucks

1 Answer

Srs light 03 accent


Was the car wrecked? If so did airbags deploy? If so any time a airbag deploy srs module must be replace. It is possible something spilled on it .

Mar 15, 2013 | 2003 Hyundai Accent

1 Answer

Both the check engine light and the airbag light have come on


The two lights you mention are also two separate systems in the vehicle. There is always a code set when the Check Engine light comes on. Find an OBDII scanner & scan the ECU (Engine Control Unit) to find any codes. I need to know which code(s), there may be more than one. The Airbag light is a proprietary (Hyundai specific) system with unique coding. That particular system can only be diagnosed by a qualified Hyundai Technician and the appropriate scan device (Hi-ScanPro). Check with your nearest Hyundai Dealership... I doubt that 1999 Accent is still under warranty.

Nov 14, 2010 | 1999 Hyundai Accent

1 Answer

Airbag light wont go off for hynadai acemt


The communication with SRS CM (Supplemental Restraint System Control Module) is proprietary - Hyundai Dealership Scanner equipment. Best solution: Take the vehicle into a Hyundai Service Center (dealership), pay the diagnostic fee. They will tell you EXACTLY what the problem is and what's needed to fix it (parts, labor, tax, time-frame, etc.).

Jun 27, 2009 | Hyundai Motor 2004 Sonata

1 Answer

2005 hyundai accent wont start


try this? remove all spark plugs and dry them out use a heat source ie gas hob? if wife permits?? then spin engine over to clear cyl/s and refit warmed up plugs ? if you have wd40 or ignition damp start? spray all ign coils/leads electrical connections/ or see if wife will let you use hair dryer and carefully blow ign leads/coils etc then try restart ? this may be a simple case of damp plugs/ignition and engine/plugs are flooded from dampness trying to start after snow ? wish you luck please update on progress

Dec 31, 2008 | 2000 Hyundai Accent

1 Answer

Need to Install A Passenger Airbag in Hyundai Accent 2002


on the 2002 Accent we have, the area is clearly identified w/the "cutout" area and marked SRS Airbag...perhaps look at Hyundai.com at the owners' manual online, or look at used cars/junk yards to compare dash panels to yours...would think it VERY difficult for avg person to perform this task

Aug 17, 2008 | 2002 Hyundai Accent

Not finding what you are looking for?
1997 Hyundai Accent Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...