1999 Dodge Ram Logo

Related Topics:

Posted on Dec 18, 2009

Wiper delay is not working already replace the multifuction sw assy

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 3 Answers
  • Posted on Dec 22, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Dec 19, 2009
Answers
3
Questions
1
Helped
608
Points
6

It may be a loose wire in the multi function switch connector that is connected to the multi function switch. The Haynes repair manual #30041 will show you step by step how to get to the switch.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

2009 Pontiac G6 Pulse setting on wipers. When on pulse the wiper goes halfway. After the next interval they go the remainder then return properly.

You didn't take into account the wiper switch is a input to the BCM - body control module ,or do you know that ? The BCM controls wiper one an wiper two relay's to turn on the wipers .
Wondering if it is the PCB or perhaps a physical problem? Guessing never finds the problem . Reading how they work in factory service repair info should be the first step for someone that doesn't know .
Intermittent Operation
Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wiper motor cycles. The DELAY interval is determined by a series of 5 resistors within the wiper/washer switch. During DELAY wiper operation, the signal circuit voltage is further reduced through the DELAY resistors. The body control module (BCM) monitors the voltage on the signal circuit to determine the delay interval between the low speed wiper motor cycles.
If the wiper switch is moved from a longer delay interval to a shorter delay interval, the BCM will command an immediate wipe cycle and reset the delay timer to the shorter delay interval.
Additionally, intermittent wiper operation is vehicle speed sensitive. As vehicle speed is increased or decreased, the wiper interval will also increase or decrease.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit and energizes the wiper 1 relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool by commanding Wiper Relay Cmd. ON and OFF.
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper 1 and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper 1 relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During HIGH speed wiper motor operation, the wiper switch signal circuit is at the LOW speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper 1 relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIPER/SW 10A fuse
• WIPER 25A fuse
Refer to Master Electrical Component List.

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3715 05: Front Wiper Relay Drive Circuit Short to Battery or Open

Your best bet , take it to a qualified repair shop.
1helpful
2answers

Why my windshield wiper only works on high and don't work on delay?

There is a wiper delay module under the dash that has failed. Windshield Wiper Switch MOTORCRAFT SW-5665
1helpful
1answer

2001 firebird wipers stop in up position already replaced the pulse board

Usually the park switch inside the wiper motor is the fault.
2helpful
2answers

1995 jeep grand Cherokee windshield wipers will not park at bottom and wiper delay wont work

your problem is the wiper motor its self,the park position in internal,you will need to replace the motor
5helpful
3answers
3helpful
1answer

96 dodge ram 2500 wiper delay does not work. have replaced motor, switch and governor still does not work. wipers will work on slow and high.

If your wiper work on slow and high and delay does not work its wiper delay module need to be replace. Get one from a junk yard save you some cash, common on dodge vech. 04883827AA for windshield wiper motor delay module. hope that help some
0helpful
1answer

2000 Jeep Cherokee Sport, window washing does not work

the little pump inside the washer fluid reservoir is bad, replace it
4helpful
1answer

How to fix the timing on windshield wipers. when you use delay it stops in up possition not the down.

There is a switch that indicats to the control module the wipers are down and parked, it is called the park switch, it is part of the wiper motor and in order to fix the issue you will have to replace the entire windshield wiper motor assy.
Not finding what you are looking for?

199 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...