Replacing front wheel bearings on 2002 new bettle

Wheel Bearings

Print
Adjustment

2002-05 Models

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   
   Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).

Removal & Installation

2002-05 Models

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   
   Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.

To install:

1. Pack the wheel bearings with grease for assembly.
2. Install or connect the following:
   
   Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel
   

front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

pull wheel remove grease cap undo carter key remove nut pull off rest of hub take bearings frt and rear out of hub clean old grease from bearings check bearing for defect install in revers order remender to install new grease in new bearings lots of grease and u will need new seals for same front and rear

Check Tires for feather edge. Join your fingers together, move around the rear Tire from front to back and vice versa on both of the rear Tires and feel the smoothness. If the tread of the Tire resist the fingers in one direction and smooth on the other, then the Tires may be producing the abnormal noise.
Temporarily bring both the front Tires to the rear and rear Tires to the front on the same side, drive the car and watch the noise. If the noise begins to come from the front end, then the Tires are defective and need replacement. . If the noise still comes from the rear wheels then the rear wheel bearings need replacement.(You can also rotate the Tires in criss cross manner temporarily)
The bearings often vary noise with and without load. Be sure to troubleshoot the noise before spending money on costlier spares.

On front wheel drive models, the rear hub bearing is an assembly that bolts to the spindle.
Not sure about AllWheelDrive models.

If you're talking about the front wheel bearings, they can't be serviced. They can only be replaced. They are sealed for life (even if the life seems to be a little short).
Here's the front bearing:


I never replaced the rear bearings on my 2002 Escape 4X4, but here's a picture of the rear hub.

REMOVAL & INSTALLATION Except Miata FRONT

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Steering knuckle from the vehicle
   • Inner oil seal from the knuckle
3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
4. Remove or disconnect the following:
   • Bearing inner race from the front wheel hub
   • Retaining ring from within the knuckle
   • Front wheel bearing from the knuckle, using the hub puller tools
   • Brake dust shield
5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
   
6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
7. Using the press tools, press a new wheel bearing into the knuckle assembly.
8. Install or connect the following:
   • Wheel bearing retaining ring
   • New oil seal using Installation tool 49 V001 795
   • Front wheel hub using the Mazda press tools

REAR

1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
   
2. Remove or disconnect the following:
   • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar)
     
     
   • Brake drum, if equipped
   • Rear caliper and rotor assembly from the hub, if equipped
   • Hub dust cover
3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
4. Remove or disconnect the following:
   • Hub retaining nut and discard it
   • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle
     
   To install:
   
5. Install or connect the following:
   • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
   • Stake the nut into the groove in the spindle
   • Dust cover
   • Assemble the brakes
   • Rear wheel

A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

if you have rear abs then yes. you may have pinched the cabl attached to the wheel bearing

Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.