Honda jazz mirror lamp replacement, how do you remove the mirror to do this?

Replacing the tailgate lock on a Honda Jazz 2014 involves several steps. Here's a general outline of the process:

1. Open the tailgate: Begin by opening the tailgate and locating the lock mechanism.
2. Remove the trim panel: You will need to remove the trim panel that covers the tailgate lock mechanism. This may require the use of a trim tool or a screwdriver, depending on the exact model of your Honda Jazz.
3. Disconnect the electrical connections: After removing the trim panel, you will need to disconnect any electrical connections that are attached to the lock mechanism. This will likely involve disconnecting the wires from the tailgate lock switch.
4. Remove the old lock mechanism: Next, you will need to remove the old lock mechanism. This may require the use of a socket wrench or pliers, depending on the type of mechanism that is installed.
5. Install the new lock mechanism: Once the old lock mechanism has been removed, you can install the new one. Make sure that the mechanism is securely fastened and that all electrical connections are properly reattached.
6. Reinstall the trim panel: Finally, reinstall the trim panel that covers the lock mechanism.

It is important to note that this process can vary depending on the exact model of your Honda Jazz, so it is always a good idea to consult your owner's manual or a professional mechanic for specific instructions and guidance. Additionally, it is recommended that you wear protective gloves and safety glasses when working on the tailgate lock to avoid injury.

To fit it you need to pop off the mirror plate itself, remove the (7 I think) screws to access the wing mirror cover clips. Squeeze those to release the cover, remove the cover to expose the indictor unit which can then be unscrewed (2 screws) and the push-on electric plug removed. Reverse for putting back together.

Pretty easy. The hardest part was getting the mirror off gently.

Hope that helps. Unfortunately I didn't take pics, but is really straightforward.

The fuse is in the mirror itself.
https://www.youtube.com/watch?v=c7hhtl1a2sc

Go to Connemera Market, Palayan, Trivandrum. I've seen so many of it there.

It is in the fender well. Remove the clips, fold back the liner, (might have a screw, too) The pump just pulls out of the reservoir. Don't get wet!

With the help of diagnostic computer go to EPS and clear the present and history error codes, if any. This problem usually arises when replacing the battery.

Jacker

conner you are 10 years late.
so manual on fails
and door open dome fails, and the switch not set to ALL MOdes off?
hhhhhhhhhhhh read the users guide on dome lamp.
oops no jAZZ in USA, so no books
most cars 2007 the lamps are BCM body brain operated
and have no dedicated fuse to DOME at all, like seen in the 1990s' back.
the best I can guess is the head lamp switch if you looked close has dome option. there.
on, off, auto
off makes it dead all the time
auto makes door switchs turn on dome.
most cars are in fact fully programmable by you and is cover in the jazz operator guide in the glove box day1, new, lost it?
HONDA has it ,ask them, it is free.

here are the words you never read,in the glove box
as you can sees this is no 1990 are it has a brain now.
that fools many now.(then) this magic prevents battery dead.
we love it, for sure stranded by lamps left on.

Likely to be the actuator/motor inside that has failed. Order one off eBay that offers returns an find out how to fit it. Should be job done!
If not its likely to be a more serious electrical issue good luck with that..

- Disconnect the two wire connectors from the horn.
- Connect a test lamp across these two wires.
- Switch on the ignition, and press the horn button.
- If the lamp glows while pressing the horn button, replace the horn.
If the lamp does not glow:
- Check the fuse.
- Wiring.
- Steering wheel assembly.

door pad removal look for little pop outs take the pop outs off and thenremove screw then remove the mirror cover then pull on the bottom of door then pull on the side and then pull off trim up and out then you will see a vapor barrier remove it then you see the inside handlejust acouple of srews /please rate my response thank you very much