Cylinder 8 misfire, restricted performance is also coming on

The other thing would be the injector for 5.

You might have bad connection in wire harness, Wiggle the wires while reving the engine. Do this at night to see any sparks in the dark. Look for sparks around the Spark coil. You may need new coil.

All fault codes can be checked out at http://www.bluejag.co.uk but here are the results for some of yours. You can ignor P1111. Looks like a faulty plug or coil pack cylinder 2

Fault Code:- P1314 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire rate catalyst damage -bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- ECM Default:- Maximum engine speed reduced


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
Fault Code:- P1316 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure

Fault Code:-
P0302 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire detected ?€" cylinder 2

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.

Possible Fault:- Refer to P0300 Possible Causes

DTC P0037; RIGHT-HAND CATALYST MONITOR SENSOR HEATER CONTROL CIRCUIT LOW/HIGH RESISTANCE
DTC P0300; RANDOM MISFIRE DETECTED, MISFIRE DETECTED, PRIMARY CIRCUIT MALFUNCTION
DTC P0305; RANDOM MISFIRE DETECTED, MISFIRE DETECTED,
P1316 IS A MISFIRED OF A CATALYST FOR EX.SPARK PLUG,INJECTOR PRESSURE ,IN GENERAL ITS THE MISFIRED DRIVE CYCLE ...SOMETHING IS FIRING PROPERLY..LET ME ASK HOW MANY MILES DO YOU HAVE.?AND CODE P1111 IS NOTHING TO BE WORRIED ABOUT ITS THE SYSTEM READINESS TEST THAT THE CARS ECM PERFORMS WHEN YOU CUT IT OFF EACH TIME...MAKES SURE THAT ALL IS FUNCTING WELL.

Misfire could be a number of things:
a) spark plugs - change them if used over 15K miles - inspect/regap.
b) spark plug wires - change them if over 15K miles - inspect
c) ECM (electronic control module) - test with HEI (high energy ignition) tester.

The vibrating tells me that the engine is running on less than its normal compliment of cylinders - the shaking is produced by the imbalance caused in the engine by one (or more) cylinder(s)
not firing at all.

The "Check Engine" light probably is coming on due the the misfire condition. Go to Pep Boys or
Advance Auto Pats, where they'll tell you (free) your codes causing the "Check Engine' light to be
lit - the code coming from your truck's computer will probably be one or more of:
P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

Misfire could be a number of things:
a) spark plugs - change them if used over 15K miles - inspect/regap.
b) spark plug wires - change them if over 15K miles - inspect
c) ECM (electronic control module) - test with HEI (high energy ignition) tester.

The shaking tells me that the engine is running on less than its normal compliment of cylinders - the shaking is produced by the imbalance caused in the engine by one (or more) cylinder(s)
not firing at all.

The "Check Engine" light probably is coming on due the the misfire condition. Go to Pep Boys or
Advance Auto Pats, where they'll tell you (free) your codes causing the "Check Engine' light to be
lit - the code coming from your truck's computer will probably be one or more of:
P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

U NEED TO GET THE CAR SCANNED SO U CAN PINPOINT WHAT CYLINDER IS MISFIRING. AFTER THAT WE START THE REPAIR PROCESS. WETHER ITS A DEFECTIVE COIL,BOOT OR SPARK PLUG. YOUR LOCAL AUTOZONE DOES IT FOR FREE

I had the same problem. Restricted performance and running rough at 3000 RPM. I have an OBDII code reader and found that the problem was in the air mass flow sensor, which is just after the air filter. I pulled this out and found it was dirty and had butterfly wings in it. The last shop where I had the oil changed replaced the filter for me but put in the wrong size. Close but no cigar. Bought some *** Flow Sensor cleaner at auto store and fixed the problem. Get an OBDII reader with the ability to erase the codes. Comes in real handy.

Code P0301
Ignition Coil Pack
Ignition Cable
Spark plug
Clog or dirty fuel injector
Evap canister purge valve
Engine Compression
fuel pressure

you have 3 type of engine for your truck
2.3L 4 cylinder
3.0L 6 Cylinder
4.0L 6 Cylinder

need to know that type Engine

The reason why the service light come on because it is a hard code
not a soft code.

Let me know

2000-2002 S-Types are horrible for this problem. Especially around 80,000 miles or more.
You are feeling a misfire(s). If no check engine light, then the computer can't determine exactly which cylinder is misfiring. Yes the coils are under the black covers on top of the cam(valve) covers. One per clyinder. I would recommend replacing all eight as the new coils are a newer design and if you just replace one now you will be replacing them one by one very soon. Make sure the tech inspects the cam(valve)cover seals for leaking, as they are bad to leak into the spark plug wells and cause same problem. Also change spark plugs as well at this time. Good luck!