Central locking not working i have 2 keys for my car 1 did not work last night i switched to the second key which locked her last night come the morning none of thekeys would unlock my car could it be a fuse problem or could the rin effect the sensor ? please help thanks in advance richie
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Try replacing the FOB battery. Check the fuse for door locks. usually located in the engine bay fuse box. Temporarily you can lock the other doors from inside the van and lock the driver door last using the key. Another possibility is that the locking switch in the driver door is faulty or the central locking motor is. All other doors will only lock if the driver door locking system works. When you lock the driver door, the locking motor will hit a switch that will lock the other doors.
1 Programming When Key batteries completely discharged. Key batteries not replaced within 60 seconds. Key added or replaced. DO NOT press remote control buttons during battery replacement. How Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button Fig. 1 [1]. Press lock button Fig. 1 [2] briefly 3 times within 10 seconds keeping unlock button [1] depressed. Release unlock button Fig. 1 [1]. Some models: LED Fig. 1 [3] flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Some models: Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously
Later keys with bmw badge on key. Battery can not be replaced
Battery in key charges while driving
Telephone: Fax: VAT Registration No.: Infrared remote control NOTE: Infrared emitter can be seen at front edge of key. System operation Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system. Programming When Key batteries completely discharged. Key batteries not replaced within 15 seconds. Key added or replaced. System malfunction. How Obtain all keys fitted with remote control. Turn ignition switch to position I. Wait approximately 10 seconds. Ensure clock LED illuminates. NOTE: LED illuminates for approximately 5 seconds. Switch ignition OFF and remove key, while LED illuminated. Programming mode activated for approximately 20 seconds (LED illuminated). Proceed as follows: Point key at receiver (located near interior lamp). Press and hold unlock button Fig. 1 [1]. After approximately 1 second key LED will flash once [3]. Press lock button 3 times Fig. 1 [2]. Release unlock button Fig. 1 [1]. Continue to point key at receiver until LEDs in clock and key have flashed 5 times. Ensure LED remains illuminated. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode and extinguish clock LED: Switch ignition ON and OFF. Wait approximately 20 seconds. NOTE: A maximum of 4 keys can be programmed. Fig. 1 Radio frequency remote control System operation Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds.
Pressing tailgate release button twice within 3 seconds unlocks the tailgate - if fitted. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system. Interior lamp illuminates when disarming system. Programming When Key added or replaced. System malfunction. How Obtain all keys fitted with remote control. Fasten seat belts and close all doors. From position I, turn ignition switch as follows: To position II. To position I. To position II. To position I. To position II. To position I. Programming mode activated for approximately 20 seconds. LED or fog lamps ON warning lamp illuminates (some models) or the system will emit an acoustic signal to indicate start of programming mode. Proceed as follows: Type 1: Press and hold unlock button Fig. 1 [1]. Type 2: Press unlock button Fig. 2 [2]. Ensure clock LED or fog lamps ON warning lamp flashes (some models) or wait for acoustic signal (indicates correct programming). Wait 2 seconds. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode: Switch ignition ON. Wait 20 seconds. NOTE: A maximum of 4 keys can be programmed.
Method 1: Press lock or unlock button 4 times in succession. Method 2: Switch ignition ON and OFF. Within 10 seconds press lock and unlock button in succession.
This is the only manual reset
If this does not work go to your local auto electrician
The probable fault could be central locking activator passenger door
Providing no faults on central locking,and battery in key is ok try reprograming key
Switch ignition on
PRESS AND HOLD lock button 10 seconds
Switch ignition off
Remove key
Wait 5 seconds
Check central locking has reset
Programming When Key batteries completely discharged. Key batteries not replaced within 60 seconds. Key added or replaced. DO NOT press remote control buttons during battery replacement. How Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button Fig. 1 [1]. Press lock button Fig. 1 [2] briefly 3 times within 10 seconds keeping unlock button [1] depressed. Release unlock button Fig. 1 [1]. Some models: LED Fig. 1 [3] flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Some models: Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously
To change batteries remove panel back of key then screws on plastic bar
Batteries are available from your local motor factor shop
You might not need new batteries try re programing as described above
Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.
You must reset your remote control in order for the lock/unlock to work properly.
To reset remote you would: 1)Insert Key in Ignition Turn to Position 1(Don't Start the Engine) for about 5 seconds 2)Turn Key Off and HOLD the LOCK button on Remote while pressing the UNLOCK 3 TIMES 3)Release both lock and unlock buttons you are holding 4)All doors should automatically unlock
Maybe you can try this procedure to resyn your key. Initialization Procedure.
1. Open central locking system using the car key. 2. Get into the car and close all doors. 3. Using the car key, switch the ignition lock briefly to position "1" and then switch off again. (Please do this switching within 5 seconds or otherwise the system is not ready for initialization. 4. At the remote control key. Press the "OPEN" key (->) and keep holding. 5. When holding the "OPEN" key, press the "LOCK" button three time. 6. After pressing the "LOCK" button 3 times, release the "OPEN" button. 7. If the initialization process is sucessful, the door will lock and unlock immediately to confirm the process.
×