Where is the camshaft sensor located? - 1996 GMC Safari

The camshaft position sensor on a Peugeot 3008 can be located in different positions depending on the engine model and year of manufacture. Here are the possible locations:

1. On the engine cylinder head: In some Peugeot 3008 models, the camshaft position sensor is mounted on the engine cylinder head, near the camshaft.
2. Near the timing belt cover: In some other models, the camshaft position sensor is located near the timing belt cover. It can be either on the engine block or on the cylinder head.
3. Behind the camshaft pulley: In some Peugeot 3008 models, the camshaft position sensor is located behind the camshaft pulley.

To locate the camshaft position sensor on your specific Peugeot 3008 model, you should consult your owner's manual or a repair manual for your vehicle. Alternatively, you can seek the assistance of a professional mechanic or a Peugeot dealer.

Top part says you want Camshaft Sensor, but the bottom says you want Crankshaft Sensor??

Camshaft
https://www.google.com/search?q=2012+dodge+caliber+3.0+camshaft+sensor+location

Crankshaft
https://www.google.com/search?q=2012+dodge+caliber+3.0+crankshaft+sensor+location

..

There is two sensor one one each head here is a guide to help walk you through the replacement and the location of the sensors in the diagrams below.

https://www.2carpros.com/articles/camshaft-angle-sensor-replacement

LOCATION
The camshaft position sensor is located on the rear cylinder bank in front of the exhaust camshaft. The camshaft position sensor extends into the rear cylinder head and is sealed with an O-ring.

The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor



and next the location of 2003 ford focus camshafts position sensor

2.4L cmp sensor exhaust located upper rear of the engine near camshaft cover. 2.4L cmp sensor intake located upper front of the engine near the camshaft cover. the 3.5L cmp sensor located right side of engine compartment above the timing chain cover.below power steering pump.3.6L cmp sensor located right side of the engine near the front and rear.

The crank sensor is on the lower rear side of the block.

the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps