Question about 1992 Ford Crown Victoria
Posted on Nov 16, 2009
Standing in front of car, on top of intake magafold, towards back of intake on top. Remove connector and 2 small bolts holding EGR valve, remove EGR valve and replace.
Posted on Nov 16, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,
Posted on Feb 05, 2009
ha ha thats a fun one.. look on the drivers side of engine next to the firewall, behind the throttle body.
Posted on Jan 05, 2009
SOURCE: Location of EGR Valve
Found the info!!
This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!
Posted on Mar 14, 2009
The link below is a diagram of the EGR valve. Looks like a mushroom with vacuum lines attached.
I hope this answers your question. Best of luck.
Posted on May 30, 2009
Tips for a great answer:
Aug 16, 2013 | 1995 Chevrolet Cavalier
Oct 30, 2010 | 2003 Chevrolet Impala
May 26, 2010 | 1994 Buick LeSabre
Aug 16, 2009 | 2000 Chevrolet Silverado
Jun 06, 2009 | 1994 Oldsmobile Bravada
Mar 14, 2009 | 2005 Dodge Dakota
Feb 05, 2009 | 2005 Dodge Ram 1500
10,037 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: