The oil sensor needs to be replaced where is it

VM 2.5 WAS USED IN 1999 JEEPS
SEEN IN EUROPE
OR AS SOME SAY
located behind the oil filter assy above the engine mount
13PSI IS MIN,FOR SENSOR TRIP. JEEP XJ
THE SERVICE MANUAL SHOWS IT HERE
FIGURE 26 LHD 2.5VM 1999 YEAR JEEP

It is there somewhere, but that's all I can say as you have not told us the make, model, year or engine type.

crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

my sister had the same problem. There are 2 sensors that can cause this when they go bad. One is the oil pressure switch, which is located near the oil filter. When the PCM reads this switch, and gets a low reading, it will automatically kill the engine. The switch costs around $4.00 and is a 5 minute replacement job. The other possibility is that the crank position sensor has gone bad. When this sensor goes bad, the PCM can't read the appropriate speeds of the crankshaft, and will adjust the fuel and air mixture to compensate, often times the engine will die because it is getting insufficient fuel and air. The Crank position sensor is located on the engine block near the water pump. It is around $40.00 and at the most a 30 minute replacement job if you are unfamiliar with the process. I hope this helps. I'm a vehicle mechanic in the Air Force, with roughly 7 years of experience on the floor.

take the sump off and you will find it ,to get the sump off you will need to remove the engine

On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.


Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines



Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

P0118 - Engine Coolant Temperture Sensor - Circuit High Input
P0301 - Cylinder 1- Misfire Detected
P0705 - Transmission Range Sensor Switch Circuit Malfuction (PRNDL Input)

P0118 - Replace Engine coolant Temperture sensoe located by thermostat housing (upper ragiator hose connects to) sensor is 1 where wire loom lays nect to valve cover.

P0301 - bad spark plug/wire, remove #1 cylinder plug wire inspect for oil on wire (if have oil on wire, valve cover gasket leaking, needs to be replaced) if no oil, inspect plug, replace plugs if needed.

P0705 - bad neutral safty switch (Transmission Range Switch) located on Right Side of Automantic Transmission (by shifter cable)

These lights need to be reset manually. Try turn the key to ON (do not start) then pump the gas pedal 3 times.

2.9L and 4.0L engines-Left side front of the engine, below the cylinder head in the engine block

The oil light on your car has nothing to do with oil level in the crankcase but rather oil pressure. The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you have engine noise or suspect low oil pressure, I'd replace it but you could check oil pressure for peace of mind with an pressure gauge if you wish. You may need a special socket to replace it.