Question about 1999 Dodge Intrepid

1 Answer

I am trying to test the crank sensor on my 99 intrepid and need to know how to test

Posted by on

  • Anonymous Mar 27, 2014

    need to know how to test crank sensor

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

No-Start Diagnosis
The diagnostic procedure for EI (electronic ignition) systems varies depending on the vehicle make and model year. Always follow the procedure recommended in the vehicle manufacturer's service manual.
The following procedure is based on Chrysler EI systems. The crankshaft timing sensor and camshaft reference sensor in these systems are modified Hall-effect switches.
If a crank or cam sensor fails, the engine will not start. both of these sensor circuits can be checked with a voltmeter or lab scope.
If the sensors are receiving the correct amount of voltage and have good low-resistance ground circuits, their output should be a pulsing digital signal or voltmeter reading while the engine is cranking.
If any of these conditions do not exist, the circuit needs to be repaired or the sensor needs to be replaced. When the engine fails to start, follow these steps:

  1. Check for fault codes 11 and 43.
    • Code 11, "Ignition Reference Signal," could be caused by a defective camshaft reference signal or crankshaft timing sensor signal.
    • Code 43 is caused by low primary current in coil number 1, 2 or 3.
  2. With the engine cranking, check the voltage from the orange wire to ground on the crankshaft timing sensor and the camshaft reference sensor. i am trying to test the crank sensor on my 99 - fr_24.13.gif Crankshaft timing and camshaft reference sensor terminals.
    • Over 7V is satisfactory.
    • If the voltage is less than specified, repeat the test with the voltmeter connected from PCM (powertrain control module) terminal 7 to ground.
    • If the voltage is satisfactory at terminal 7 but low at the sensor orange wire, repair the open circuit or high resistance in the orange wire.
    • If the voltage is low at terminal 7, the PCM may need replacement.
      • Be sure 12V are supplied to the PCM terminal 3 with the ignition switch off or on, and 12 V must be supplied to PCM terminal 9 with the ignition switch on.
      • Check PCM ground connections on terminals 11 and 12 before PCM replacement.
  3. With the ignition switch on, check the voltage drop across the ground circuit (black/light blue wire) on the crankshaft timing sensor and the camshaft reference sensor.
    • A reading below 0.2V is satisfactory.
NOTE When using a digital voltmeter to check a crankshaft or camshaft sensor signal, crank the engine a very small amount at a time and observe the voltmeter. The voltmeter reading should cycle from almost 0 volts to a highter voltage of about 5 volts. Since digital voltmeters do not react instantly, it is difficult to see the change in voltmeter reading if the engine is cranked continually.
  1. If the readings in the previous two steps are satisfactory, connect a lab scope or digital voltmeter from the gray/black wire on the crankshaft timing sensor and the tan/yellow wire on the camshaft reference sensor to ground. fr_24.14.gif Lab scope patterns from the camshaft and crankshaft position sensors.
    • When the engine is cranking, a digital pattern should be displayed or the voltmeter should cycle between 0 and 5 volts.
    • If the voltage does not cycle, sensor replacement is required.
    • Each sensor voltage signal should cycle from low voltage to high voltage as the engine is cranked.
A no-start condition can occur if the PCM "locks up."
  • In step 2 above, if 0 volts is indicated the PCM may be faulty or it may be locked up.
  • If the PCM is locked up it will not store a fault code for the reason.
  • Basically, the PCM will lock up when it goes into a safeguard routine if the 9-volt or 5-volt reference voltage shorts to ground. This shuts down the PCM to protect it. Since it shuts down, no DTCs (Diagnostic trouble code) are stored.
  • The engine will not start as long as the ground is present. An intermittent ground will cause the engine to stop running.
  • Attempting to restart the engine without cycling the ignition switch to the full LOCK position will not start the engine, even if the ground is lifted.
    • Cycle the ignition switch to the LOCK position and wait about 5 to 10 seconds.
    • If the ground is lifted, the PCM will reset and the engine will start and run until the ground occurs again.
  • On 1996 and new SBEC III and JTEC engine controllers, there are two 5-volt reference signals. The sensors that require 5 volts are separated, thus If this signal shorts to ground the engine will still stop running, but for the first time a DTC can be set.
  • Also note, if the 9-volt reference voltage is opened, there will be no DTC stored for the crankshaft or camshaft positions sensors. With an open circuit the PCM cannot tell if the engine is cranking or not. The diagnostic routing does not begin until the PCM senses engine cranking.

Posted on Nov 10, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 84949 Answers

SOURCE: 99 intrepid 2.7

U NEED A SCANNER WITH LIVE DATA ABILITY.

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 intrepid 2.7


U NEED A SCANNER WITH LIVE DATA ABILITY.

Nov 10, 2009 | 1999 Dodge Intrepid

1 Answer

99 dodge stratus dies while driving


Were the plugs covered in oil? With the plugs that go through the valve cover you might need new seals. Did you replace the plug wires? You need to scan it for codes. It's most likely a missfire, but it could be a bad speed sensor (also called, VSS vehicle speed sensor, cam position sensor,or crank position sensor).

Jul 27, 2009 | 1995 Dodge Intrepid

1 Answer

Location of speed sensor a for 99 dodge intrepid


The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Mar 29, 2009 | 1999 Dodge Intrepid

1 Answer

99 intrepid 2.7 engine cranks alot to get started


Did the old engine start ok? If so then take a good look at the Crank Position Sensor or the flywheel sensor ring. Some times the flywheel ring can get bent/damaged during an engine swap. It doesn't take much to dent that ring and it is really close to the CPS. The other thing you can try is turn the key on without starting several times before cranking. This will pulse the fuel pump each time and charge up the fuel pressure. If that works you have a fuel pressure issue (probably a pump) Let me know how it goes.

Mar 28, 2009 | 1999 Dodge Intrepid

2 Answers

99 intriped, Drives great but will turn off at ramdom


when it cranks and does not run does it have spark?

Feb 01, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

1,157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

84949 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...