Need fire order,spark plug wires replaced in incorrect place

It can be faulty or dirty spark plug itselfd.Also for reference get the fuel level checked.Is the fuel tank is empty or near to empty.
Try cleaning the spark plugs and then see if that is helpin.On some cases the black carbon layer gets collected on the spark plugs and that causes the problem,so cleaning the plugs help.But if its not helping,then spark plug has to be replaced.Spark plugs get power from ignition coil to ignite sparks.If ignitioncoils are faulty then also there will no spark.--------------

To troubleshot and confirm the issue,i suggest you to go through the help links provided below,check the procedure and it will help you to confirm the issue in your case.
----------
Click the link below:------

Car cranks, has spark but will not ?

http://howtobyme.blogspot.com/2011/12/car-crankshas-spark-but-will-not-start.html

-----------

The spark plug firing order for car?

http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html

------------

How to Replace Spark Plugs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html

---------------

How to Perform a Basic Engine Tune Up-Spark Plug and Wire Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up_01.html

----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

---------

How does the spark plug wire go on the distributor cap in 1991 Mitsubishi Mighty?

http://schematicsdiagram.blogspot.com/2011/12/how-does-spark-plug-wires-go-on.html

------------
No spark on 2008 Chevy Avalanche?

http://schematicsdiagram.blogspot.in/2012/04/no-spark-on-2008-chevy-avalanche.html

-----------

How does the spark plug wire go on the distributor cap in 1985 Pontiac sunbird?

http://schematicsdiagram.blogspot.com/2011/12/how-does-spark-plug-wire-go-on.html

--------------

Ford Plug Wires Not Coming out?

http://whoisbyme.blogspot.in/2012/06/ford-plug-wires-not-coming-out.html

--------

Ford explorer has no spark?

http://schematicsdiagram.blogspot.com/2011/12/ford-explorer-has-no-spark.html

----------

Chevy impala spark plug firing order diagrams?

http://technoanswers.blogspot.in/2012/02/chevy-impala-spark-plug-firing-order.html

------------

How to gap spark plug on Chevy Impala?

http://technoanswers.blogspot.in/2012/02/how-to-gap-spark-plug-on-chevy-impala.html

-----------

Spark plug Replacing for chevy impala?

http://technoanswers.blogspot.in/2012/02/spark-plug-replacing-for-chevy-impala.html

Chevy s-10 blazer 4.3l Spark Plug Firing Order?

http://howtobyme.blogspot.com/2011/12/chevy-s-10-blazer-43l-spark-plug-firing.html

----------------

1982 dodge rampage Spark plugs Firing Order Diagram?

http://schematicsdiagram.blogspot.com/2011/12/1982-dodge-rampage-spark-plug-firing.html

----------------

2006 Suzuki Forenza Spark plug Firing Order Diagram?

http://schematicsdiagram.blogspot.com/2011/12/2006-suzuki-forenza-spark-plug-firing.html

------------

1983 Ford Ranger Spark plug firing order?

http://schematicsdiagram.blogspot.com/2011/12/1983-ford-ranger-spark-plug-firing.html

--------

Firing Order for 1991 Lexus ES 250?

http://schematicsdiagram.blogspot.com/2011/12/firing-order-for-1991-lexus-es-250.html

----------------

Firing order for 1992 Chevrolet 5.0 engine?

http://schematicsdiagram.blogspot.com/2011/12/firing-order-for-1992-chevrolet-50.html

-----------

How to identify number one spark plug on the distributor cap?

http://schematicsdiagram.blogspot.com/2011/12/how-to-identify-number-one-spark-plug.html

-----------

How to remove rear spark plugs on 1991 Buick Regal?

http://howtobyme.blogspot.in/2012/02/how-to-remove-rear-spark-plugs-on-1991.html

---------------

These details will help.

Thanks.

It sounds like the spark plug wires are not plugged into the correct place on the distrubutor. take the distributor cap off and crank the engine over. Make a note of which direction the rotor spins. (Clockwise, or Counterclockwise) then find the firing order for that engine. Sometimes the firing order is on the intake manifold. (if you tell me which engine it has, the 4 cylinder 2.0, or the 6 cylinder 2.5; I could post you the firing order). Now on the distributor cap there is one wire post that has the #1 on it, that would be where you put the spark plug wire from cylinder 1. Following the rotation of the distributor rotor, you would put the spark plug wire for the next cylinder in the firing order after the #1 wire, and so on.

you need to get a diaghram on the firing order of your spark plug

wires, almost any autoparts store will give you the firing order for

your vehicle. if the firing order is incorrect the engine can sound

like its falling apart. the spark plugs also need to be gapped

correctly, they are not always pre-gapped or check the gap of

one of your old spark plugs and match the gap with the new ones.

good luck!

If your trying to change spark plugs remove one wire from a plug, replace that plug, reinstall the wire onto that plug and move on to the next plug. You don;t need to worry about firing order unless you plan on changing the wires or the cap and rotor. Even if you where to change the wires if you did them one at a time than the new ones would be in the exact same place as the old ones and there is nothing to worry about,

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

the firing order should be - 1-6-5-4-3-2 , Front Bank 1-3-5, Rear Bank 2-4-6. Hope this helps.

carsandcomps,

Guru, Premium Expert @ Fixya.com

TIP: When replacing spark plugs and wires, do one at a time to ensure each is placed back in it's original position and place.

i would check the order the leads go from the distributor to the spark plugs as 1 or 2 of these might be incorrectly placed on the wrong spark plugs causing the mis-firing.

HI. There are several areas of concern here. I will list them below. Check all areas stated in the list for faults.

Possible cuases:

1. Incorrect firing order set. On the 2.0, 2.4 and 2.7 engines. These engines are equipped with a distributor-less ignition system. This system incorporates a coil pack assembly, along with wire sets. In order for the assembly to fire correctly, the order of the wires must be set to the proper sequence. if not, the engine will not turn over, or start correctly. Make sure your firing order is correct, and make sure you have not placed a particular wire set into the wrong cylinder. I will post a picture of the correct firing order for your engine, below this list, shortly.


2. Incorrect spark plug gapping procedure. If the new spark plugs were gapped incorrectly, this will not allow for proper spark, thus, preventing optimal combustion, due to lack of fire. Check the spark plug gap using a wire gap gauge, and adjust if necessary. The gap should be 0.039-0.043 in. (1.0-1.1mm)

3. Failed coil pack assembly. This will be the worst case scenario. The coil pack supplies the necessary current that fuels each plug. The current is transferred, via wire sets.This will be the culprit if all the above areas are proven to be operational, and in good shape.

4. Failed wire sets. Replace the wire sets if faults are found at the connector at the ignition coil pack, or at the plug boot.



NOTE*
In order to provide the correct firing order for your engine, i will need the engine size and liter information, if possible. Please post this information, asap. Thanks..

The cylinder order is 1,2,3 (rear row, left-to-right) and then 4,5,6 (front row, left-to-right).
When replacing spark plug wires or plugs, it's very helpful to do one at a time to avoid connecting them incorrectly.
Hope this helps, Sherwin

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
   NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
2. Remove the intake manifold cover, if required.
3. Disconnect the left side spark plug wires from the spark plugs.
4. Disconnect the left side spark plug wires from the ignition coil.
5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
6. Remove the spark plug wire assembly.
7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
8. Disconnect the right side spark plug wires from the spark plugs.
9. Disconnect the right side spark plugs from the ignition coils.
10. Remove the spark plug wire assembly.
11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.

To install:

1. Install the spark plug wire assembly.
2. Connect the right side spark plugs to the ignition coils.
3. Connect the right side spark plug wires to the spark plugs.
4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
5. Install the spark plug wire assembly.
6. Connect the left side spark plug wires to the spark plugs.
7. Connect the left side spark plug wires to the ignition coil.
8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system


Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system


I really hope help you with this (remember rated this help) Good luck.