REMOVAL OF THE RADIO - 1992 Eagle Talon

Mazda MPV Dash Trim Removal, Stereo Removal - Auto ...

? 3:38
https://www.youtube.com/watch?v=REoTeVM2S-o
Jul 1, 2013 - Uploaded by Robert DIY
Dash trim removal: 5 minutes. This video will show you how toremove the dash trim piece on the Mazda ...

[PDF]MAZDA 1996-UP MPV - Scosche

www.scosche.com/media/guides/ma381.pdf

164. 1996-UP MAZDA MPV. MINIVAN. RADIO REMOVAL USING SCOSCHE DT-1 TOOLS . FRONT DOOR PANEL. FRONT AND REAR DOOR 61/2" 3-HOLE.

DIY Mazda Car Radio and Speaker Removal, How to Remove

www.carstereoremoval.com/htm/stereoremovalMazda.htm

'96-99* Car Stereo Removal · Ford Stereo Removal Tools Stereo Removal Tools. How To Install and Remove Mazda MPV Van Car Radio and Speaker, '89-95*

You need a radio removal tool. You can buy them most anywhere. They even sell them at Wal Mart Click the following link to see them.

http://www.walmart.com/ip/Scosche-DIN-Radio-Removal-Tool/870835

you need the radio removal u shaped tools. you can buy for $5 at uto store.

SECTION 415-01: Audio Unit 2002 Escape Workshop Manual
REMOVAL AND INSTALLATION Audio Unit
Special Tool(s) Radio Removing Tool
415-001 (T87P-19061-A)
Removal and Installation

1. Disconnect the battery cables. For additional information, refer to Section 414-01 .

1. Remove the audio unit.
   1. Insert the special tool into the radio face plate and release the radio retaining clips.
   1. Pull outward on the special tool and remove the audio unit from the instrument panel.

1. Disconnect the connectors.

1. To install, reverse the removal procedure.

Radio Reciever/Amplifier/Tape Player/CD Player REMOVAL & INSTALLATION Fig. 1: Remove the bezel retaining fasteners and the bezel . . .

1. Disconnect the negative battery cable.
2. Remove the center cluster screws and bezel.
3. Remove the radio attaching screws.
4. Disconnect the radio from the instrument panel wiring harness and antenna.
5. Installation is the reverse of removal. Fig. 2: . . . then remove the radio retaining fasteners
   Fig. 3: Slide the radio forward so that you may gain access to the electrical connections
   Fig. 4: Disengage the antenna and radio electrical connections
   

Hope this helps! Please don't forget to rate!


Example of the special radio removal tool


Exploded view of the radio mounting and wire connections. Note the rear support and the bracket that it attaches to

1. Disconnect the negative battery cable.
   
2. On 1991-92 models, remove the finish panel from around the radio assembly.
   

To remove the radio, insert the removal tool prongs into the release clip access holes (arrows)


Push in approximately 1 inch (25.4mm) to release the retainer clips, then pull straight out to remove

3. Insert the radio removal tool T87P-19061-A or equivalent, into the radio face.

4.Press in 1 inch (25.4mm) to release the retaining clips, then using the tool as handles, pull the radio out of the instrument panel.


Disconnect the antenna ...


... and the electrical wire harness plugs from the back of the radio

1. Disconnect the antenna and wiring connectors from the radio.
   

To install:

1. Connect the wiring and slide the radio into the instrument panel. Ensure that the rear mounting bracket is engaged on the mounting track in the panel.
   
2. If removed, install the finish panel
   
3. Connect the battery cable.
   
4. Check the operation of the radio.
   

YOUTUBE HAS GOOD VIDEO ON FORD CAR
RADIO REMOVAL.

Digital Audio Compact Disc Player


Section 15-01: Radio, Tape Chassis and Digital Audio Compact Disc Player 1996 Probe Workshop Manual
REMOVAL AND INSTALLATION Compact Disc Player, Digital Audio SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Radio Removing Tool T87P-19061-A
Removal

1. Disconnect the battery ground cable (14301).
   

1. Remove the instrument panel finish panel (044D70). Refer to Section 01-12 for the removal procedure.
   

1. Insert the Radio Removing Tool T87P-19061-A into the face plate holes until the tension of the tool locking into place can be felt. (There are tension clips that this tool pushes out of the way so the radio can pull out. Maybe you can insert 4 pins that will do the same thing.)
   

1. Flex outward on both sides of the radio chassis (18806) simultaneously and pull the radio chassis from the instrument panel (04320) using the tool as handles.
   
   
   
   
   

1. Disconnect the electrical connectors and the radio antenna lead in cable (18812) from the radio chassis.
   

This site gives instructions for removal of Honda radios

Link:
http://www.willmanselectronics.com/Remtips/accord_rem.htm

Youtube search for video on the removal of radio
https://www.youtube.com/watch?v=v3EABOj1_wI
Do you need this removal tool shown in the video ?
https://www.youtube.com/watch?v=7LvVRphFUAk
https://www.youtube.com/watch?v=S1oZojGzPLs

or maybe the old credit card method
https://www.youtube.com/watch?v=-Wlg2fddlOI
https://www.youtube.com/watch?v=-Wlg2fddlOI

http://www.ebay.com.au/itm/like/131597764766?chn=ps
http://www.ebay.com/itm/VW-Volkswagen-BEETLE-GOLF-PASSAT-Car-Radio-Removal-Keys-/280594916190

There should be an actual wire harness for radio back in there somewhere, maybe tied up or bundled up, just have to find it, then buy from stereo or automotive supply place, an adapter that will go from factory plug to your other stereo, and it will make installation much, much easier.