Question about 1992 Ford Crown Victoria

1 Answer

It seems like the lock-up torque converter is jumping in and out

It seems like the lock-up torque converter in my 92 Crown Victoria is jumping in and out of lock-up mode when the engine drags down, before the transmission downshifts. What could be causing this? The transmission does not seem to be slipping under hard acceleration. Just the problem with the torque.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,595 Answers

Look at the module switch

Posted on Jan 09, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 350 Answers

SOURCE: F250 2002 V10 fault code P0743 torque converter clutch circuit

hi if the torque coverter is faulty it will not run right as this is what transferes the engines power to the box change it before it damages the box that will be expensive as the metal parts in the coverter will break up and will transfere it through your box if it hasn,t allready done so best of luck yates210456

Posted on Oct 13, 2008

Anonymous

  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

Anonymous

  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

Anonymous

  • 8 Answers

SOURCE: engine will not start

check your timing belt it may be broken or timing has jump,let me know if this works,thanks

Posted on Apr 21, 2009

Dr Honeydew

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 92 crown vic cataketic converters get red hot


Your exhaust system could need to be replaced. By removing the cats you lost required back pressure that gives your car power.

Aug 30, 2014 | 1992 Ford Crown Victoria

Tip

How To Install Replace Power Window Regulator Crown Victoria Grand Marquis 92-11...


How To Install Replace Power Window Regulator Crown Victoria Grand Marquis 92-11 1AAuto.com

on May 22, 2012 | 1998 Mercury Grand Marquis

Tip

How To Install Replace Engine Air Filter Crown Victoria Grand Marquis 92-11...


How To Install Replace Engine Air Filter Crown Victoria Grand Marquis 92-11 1AAuto.com

on May 18, 2012 | 1999 Mercury Grand Marquis

1 Answer

1997 Crown Victoria: 92 crown victoria get no spark...


Attempt to change all of the spark plug wiring and spark plugs. Then start the vehicle.

May 18, 2010 | 1997 Ford Crown Victoria

1 Answer

My 2001 crown victoria jerks at 40 mph


sound like torque converter problems.scan it to check torque converter.make sure it is applying and releasing .if not you got a bad torque converter solenoid.or a stop up screen.restriction in oil passages .or the o-ring seal cut or damage.also check for low oil pressure.

Jun 25, 2009 | 2001 Ford Crown Victoria

Tip

How To Install Replace Engine Air Filter Crown Victoria Grand Marquis 92-11...


How To Install Replace Engine Air Filter Crown Victoria Grand Marquis 92-11 1AAuto.com

on May 18, 2012 | 2002 Mercury Grand Marquis

1 Answer

92 chevy lumina 3.1 Torque convert lock and unlock


replace the TCC solenoid, if that doesn't fix it you will need to replace the torque converter, it may be shorted

Jun 17, 2009 | 1992 Chevrolet Lumina

2 Answers

1985 Ford Crown Vic won't shift sometimes. Seems


Have he transmission drained and the screens cleaned

Jun 05, 2009 | 1995 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...