How do i repair left front hub & bearing assembly on a 2000 ford taurus v6 24v dohc

These video might ive you some idea:


How to Replace Front Wheel Bearing


Replace Front Wheel Bearing Hub Ford Taurus Mercury Sable


How To Install Replace Front Wheel Hub Bearing Taurus Sable 96 06 Part 1...


How To Install Front Wheel Bearing Hub Assembly 2002 05 Ford Explorer...

Check the front brake rotor. When the brake pads wear down too far they will make a grinding noise. I am not sure what sound the axle makes when they begin to wear out. I would check the boot that covers the axle joint for any damage.

How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

taurus has a hub bearing in front it will come as hub and bearing if you look behind brake caliper and around axle you will see three bolts one on top and one each side remove axle nut just push in axle some may have to hit center to free" you will see groove in axle hit there".remove caliper let hang donot remove brake line and rotor remove the three bolts and hit from top to bottom of hub it will pop out

The wheel bearings in a Ford Taurus are located in the hub/bearing assembly. Replacing the hub/bearing assembly is a straightforward process -- remove the brakes, then the bearing, and reassemble.

Not enough space available for step by step instructions. Try this link:

http://www.ehow.com/how_5488471_change-wheel-bearing-ford-taurus.html

Cheers,

TF

There's no repair to the hub bearing assembly, seal unit, to replace first remove axle nut ( 32 or 36 mm) might need some one to step on brake while removing nut, so it done turn on you, remove front brake caliper and caliper bracket, then remove brake rotor, on back side of hub bearing there three bolt's, remove, hub bearing should slide out, some time with a little help from a hammer, install new hub bearing.

Do you have the hub nut loose yet?

1. Raise and support the vehicle.
2. Remove or disconnect the following:
   
   Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
   
3. Clean and inspect the O-ring seal

To install:

1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
2. Install the O-ring to the steering knuckle (2500 series).
3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
4. Install or connect the following:
   
   Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.

You can go to autozone.com and register for free online repair manual with everything you need.

2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

The bearing might be a hub assembly in a Taurus, but it is a press in unit on a Focus. I have done it myself.