Need torque settings for big end and main bearing bolts on 1999 KIA Carnival V6 k5 2.5ltr

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

Main bearings Stage 1 34-38 Nm Main bearings Stage 2 68-76 Nm Big end bearings Stage 1 26-29 Nm Big end bearings Stage 2 53-59 Nm

MAIN BRGS: 1st stage = 25Nm (+- 1) 2nd stage = 52Nm (+- 2)
BIG END BRGS: 1st stage = 11Nm (+- 1) 2nd stage = 21Nm (+- 1) CYL HEAD BOLTS: Ist stage = 105Nm 2nd stage = 115 Nm

Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Hussain, Do not re use old bolts or nuts. As answered on fixya by Billy Rennie, big end - stage one 18-22 Nm. stage 2 40-50 degrees
main bearings stage 1 20 Nm stage 2 90 degrees
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Big end main bearing torque settings

To answer for the 2nd time, Hussain, Do not re use old bolts or nuts. As answered on fixya by Billy Rennie, big end - stage one 18-22 Nm. stage 2 40-50 degrees
main bearings stage 1 20 Nm stage 2 90 degrees
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Big end main bearing torque settings

Have a look on the link below:

kia big end torque specs Google Search

V6 colt bakkie big ends bearing torque settings

Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)

big ends 54Nm/40Ft-lbs
mains 39Nm/29Ft-lbs and mains side bolts are same torque