Question about 1997 Pontiac Sunfire

1 Answer

How do i check if it needs oil on the manual transmission because the shifts are hard to change when running or is there something else to do beside a new clutch already done

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 58 Answers

Hard shifting may be caused be the clutch not releasing properly.If you have a new clutch your problem might be caused by your hydraulic clutch release system.When stopped and idling you should be able to shift gears without grinding.Reverse grinding may indicate a clutch release problem.You should have some clutch pedal travel up from the floor before you feel it engaging.The oil fill check is either at the speedo or a plug at the axle shaft level.Be sure to use factory recommended fluid.Gear oil is not a proper fluid.

Posted on Oct 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Ford Ranger throws Trans code p0735 -- 5th gear incorrect ratio. My understanding is basically it's running without 5th gear/overdrive. (It also causes it to shift hard into/out of 2nd, as, from...


to start with there is nothing wrong with the ransmission
It is all electronic faults
the transmission is constant mesh so ratios are not manually changed by done by servos and solenoids
the fault code refers to the TR sensor that can be changed out , the hard shifting is probably dirty oil and the changing between ratios a problem TCM or wiring harness connections
if the transmission oil has not been changed in the last 60K miles , that would be a good place to start, then have the auto transmission professional service center where you are having the oil change done, check out the servo/ solenoids operations

Oct 04, 2018 | Ford Ranger Cars & Trucks

1 Answer

What qould cause a 2000 isuzu rodeo to shift hard inless u manual shift it we jave replaced transmission speed sensor lus number 4 coil pack


dirty oil is a culprit for hard changing
run fault codes to determine if it a problem servo/ solenoid or pressure problem

May 26, 2017 | Isuzu Cars & Trucks

1 Answer

Transmission shifts hard in all gear, whirring sound from tranny


check the condition of the transmission oil
check oil level
run the fault codes
change the oil and clean the oil filter
check and adjust brake bands and clutch packs while the pan is off

Aug 30, 2015 | 2001 Toyota Tacoma

1 Answer

VW 1996 Transporter T5 Shifting problems hard shifting when cold but as it warms up it shifts better.


Your fluid is either old or the wrong kind for your transmission. Changing your manual transmission fluid with a higher quality fluid should definitely reduce the difficulty of cold fluid/cold weather shifting. First go to the parts store and find out exactly what kind of fluid your transmission takes. Most manual transmission use gear oil. I recommend using something like Red Line, AMSOIL, or Royal Purple if available. A synthetic will make it even easier to shift. Always check with the manufacturer if you are unsure. I try to stick with the manufacturers recommendations because typically they know what works best with what they've engineered...but sometimes after market fluids can't be outperformed.

Nov 24, 2012 | Volkswagen Eurovan Cars & Trucks

1 Answer

Hard shifting 2002 toyota corolla manual transmission


sounds like you were running it without oil..that would explain why there was no oil leaking on the ground..the gearbox would now be worn out so it's best to get another trans,, could be a rebuilt or from a scrapped crashed vehicle..if the trans was running out of oil, best not try to repair it..

Oct 03, 2017 | 2002 Toyota Corolla

1 Answer

I have a 1986 Cutlass Supreme with a 1986 Chevy C10 engine. Im having trouble with the car shifting into Drive. The vehcile will shift fine from P R N but when it shifts into drive from reverse its a hard...


replacing the transmission is a last resort
problem could be dirty oil or spool valve problems or low oil pressure problems
take it to a professional autom transmission shop for a proper diagnosis

Feb 28, 2018 | 1986 Oldsmobile Cutlass Supreme

4 Answers

When i shift into drive on auto transmission it klunks hard on 2000 corolla


check your engine mounts, if they are broken the engine will ****.
also check your transmission fluid

Mar 09, 2010 | 2000 Toyota Corolla

3 Answers

Hard time shifting, bubbles in oil, trans not


noy sure about the hard time sifting but sounds like a vacum hose some from trans to engine may have a split in it which causes long gear change or none at all, oil brown and stinky change it its too old you should change your oil every 10 thousand

Nov 09, 2009 | 2004 Dodge Ram 2500

11 Answers

Hard Shifting 1997 5 Speed Honda Civic Manual Transmission


if its manual transmission, when moving in any gear try stepping on the gas pedal, does the engine feels like its running away? if it does it maybe the clutch lining is expended expensive job.
If not you have to check the clutch fluid level or a leak in the master cylinder (at the foot pedal) assembly or in the slave(clutch lever actuator) the clutch actuator may not be traveling (pushing) sufficiently to give you an adequate clutch separation in other words you are trying to shift the gears with little or no clutch at all.
There is an overhaul kit that you can buy (cheap) for the master or the slave. easy to do really just remove, disassemble, replace the rubber seals and cups, reinstall, bleed the air out.

Jul 27, 2008 | 1997 Honda Civic

Not finding what you are looking for?
1997 Pontiac Sunfire Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...