I need a wiring diagram for 1987 Chevrolet 3/4 ton

Partial wiring diagrams are usually available, but if you want a full wiring schematic, you need a workshop manual or a subscription to a website.

https://www.justanswer.com/chevy/2iqt1-color-code-ignition-module-1988-chev-s10.html

https://www.google.com/search?q=1987+Chevy+S10+2.8+spark+module+color+code+wiring+diagram

..

https://books.google.com/books?id=rUmRmpaOyLIC&pg=PA162&lpg=PA162&dq=87+chevy+454+crankshaft+position+sensor+location&source=bl&ots=bGi2T6mTsZ&sig=ACfU3U337cRsZ77uqDcRbxycw8RdrMxrSQ&hl=en&sa=X&ved=2ahUKEwij182Ar9D0AhUZjYkEHUmYAD0Q6AF6BAgvEAM#v=onepage&q=87%20chevy%20454%20crankshaft%20position%20sensor%20location&f=false

PDF]1980 service manual - 73-87ChevyTrucks.com. Classic ...

www.73-87chevytrucks.com/.../ST_330_80_1980_Chevrolet_Light_Tru...

Wiring diagrams for 1980 trucks are contained in a separate Wiring. Diagram Booklet.... Some of these service operations require the use of tools specially designed .... 1-1/2 Ton. 2-3/4 Ton. 3-1 Ton. 4-1/2 Ton (W/HDSusp). Fig. 0A-3-Vehicle Identification Number ... Right Hand Side of Cylinder Block at Rear of Distributor.

HEI Distributor Pickup Coil Test - YouTube

Search Results

images for wiring diagram for 350 chevy 1980
Complete 73-87 Wiring Diagrams - 73-87chevytrucks.comforum.73-87chevytrucks.com/smforum/index.php?topic=11766.0Apr 8, 2009 - 1 post - ‎1 authorHere are the complete wiring harness schematics for the 73-87 series. These are HUGE jpgs so you may want to save and print them off.[PDF]1980 Chevy - 73-87ChevyTrucks.com. Classic Chevy ...www.73-87chevytrucks.com/.../ST_330_80_1980_Chevrolet_Light_Tru...1980 Chevrolet Passenger Car and Light Duty Truck Unit Repair (Overhaul). Manual.Wiring diagrams for 1980 trucks are contained in a separate Wiring. Diagram Booklet...... 8-Cylinder Gasoline Engine Code is (305, 350, 400. CID) Located ...

Fill at side fill hole until fluid begins to run back out. Let it run until it stops, install plug and wipe up excess. If fully drained, usually holds less than 3 liters.

Remove two bolts under the dash the hold column to lower dash support, reach under and disconnect the wiring near bottom and then pull back the sound deadening and remove the bolts from the inner bulkhead, go under the hood and remove the rag joint coupler bolts, then remove the column from the truck with care to make sure you didn't miss any thing before you man handle it out like the shift indicator cable is so equipped..

Check this for 1987 Chevrolet S10/T10 P/U 2.8 liter V-6 VIN "R"




Hope this helps (remember to rating this free answer).

1998 Dodge RAM 1500

here u go.

start at the back and work forewards checking for a feed ,if feed its a ground problem ,if no feed just follow and check connectors ,all else fails run a new wire

1996 Ford F 150 2WD Pickup
4.9 liter L6


1996 Ford F 150 2WD Pickup
5.0 liter V-8

1996 Ford F 150 2WD Pickup
5.8 liter V-8