Engine light code P1507: ''manf cntrl veh spd idle speed control auxiliary inputs'' and P0306: ''cylinder 6 misfire detected''. this ranger resitates press gas. where do i start?

2006 Pontiac G6 Code P1516 Manf Cntrl Veh Spd Idle Speed

Connection to your throttle body. Get a repair kit. Here is a video explaining the problem. Just click on the link.

DTC P1572: BRAKE CANCEL SWITCH OUT OF SELF TEST RANGE NOTE: Limited information available from manufacturer.
NOTE: For circuit reference, see appropriate diagram in WIRING DIAGRAMS article.
Possible Causes

• Open circuit, high resistance or short circuit between the brake cancel switch and PCM signal circuit.
• Open or short circuit in the brake cancel switch power supply circuit.
• Brake cancel switch failure.

Misfire could be a number of things:
a) spark plugs - change them if used over 15K miles - inspect/regap.
b) spark plug wires - change them if over 15K miles - inspect
c) ECM (electronic control module) - test with HEI (high energy ignition) tester.

The shaking tells me that the engine is running on less than its normal compliment of cylinders - the shaking is produced by the imbalance caused in the engine by one (or more) cylinder(s)
not firing at all.

The "Check Engine" light probably is coming on due the the misfire condition. Go to Pep Boys or
Advance Auto Pats, where they'll tell you (free) your codes causing the "Check Engine' light to be
lit - the code coming from your truck's computer will probably be one or more of:
P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

P1354VVT System Malfunction (Bank 2)

• P0300 Random/Multiple Cylinder Misfire Detected
• P0301 Cylinder 1 Misfire Detected
• P0302 Cylinder 2 Misfire Detected
• P0303 Cylinder 3 Misfire Detected
• P0304 Cylinder 4 Misfire Detected
• P0305 Cylinder 5 Misfire Detected
• P0306 Cylinder 6 Misfire Detected
• P0307 Cylinder 7 Misfire Detected
• P0308 Cylinder 8 Misfire Detected

Probably bad plug wires. Start there and then disconnect the battery for 5 minutes reconnect and start engine to see which codes have cleared.

P0305 - Cylinder 5 Misfire Detected
P0306 - Cylinder 6 Misfire Detected

When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the Crankshaft Position (CKP) sensor signal to vary, The Powertrain Control Module (PCM) or Electronic Control Module (ECM) can determine that a misfire is occurring.

When is the code detected?
- Engine Cylinder #5 and #6 is Misfiring.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/loss of power
- Hard start
- Engine hesitation

Possible Causes:
- Improper spark plug at cylinder #5 and #6
- Insufficient compression at cylinder #5 and #6
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #5 and #6
- Fuel injector #5 and #6 may be faulty
- Intake air leak at cyli

Possible Solution:
- Perform Injector Service
- Replaced Spark Plug #5 and #6
- Replaced Injector #5 and #6
- Replaced Ignition Coil #5 and #6

Hope helps.

Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

P1521 =Manf control veh spd, idle control, auxillary inputs

P0456=Emission control system eak, very small


???Good Luck

You might just need to clean the IAC valve and throttle body. Try autozone for a free repair guide. You might need to buy a set of socket driver bits if it's held on with anti tamper screws.