I need a picture on how to take out the cylinder head on a 2000 hyundai accent 1.5

'year make model' in all questions please. Question edited and moved to Hyundai Accent.

In the link

https://www.google.com/search?q=H100+cylinder+head+bolts+torque

..

The cylinder head!!!,, ..., sounds like the valve stems seals are not working..or they forget to put them in..TAKE IT BACK!!!

torque hyundai accent Questions & Answers - Fixya

www.fixya.com > Forum > Tags

Torque specifications for cylinder head 2000 hyundai accent Are you aware that ... cover gasket on my 1997 Hyundai Accent GLS (engine code G4EH, 1.3L).

Hyundai Alpha engine - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Hyundai_Alpha_engine

WikipediaG4EH in a 1999 Hyundai Accent L ... lb·ft (132 N·m) at 4000 rpm, although some websites quote the torque rating as being 97 lb·ft (132 N·m) at 2700 rpm. ... 1992 Hyundai S-Coup? LS specifications - Carfolio.com · 1992 Hyundai S-Coup? GT ...

[PDF]AERA Torque Specs

www.aera.org/uploads/4/3/7/7/43776611/aera-torquespecs.pdf
AERA Torque Specs. 500 Coventry Lane, Suite 180, Crystal Lake, IL 60014. Toll-free Technical Hotline: 1-888-324-2372 (1-88-TECH-AERA). 815-526-7600 fax ...

.

Torque Specifications - AutoZone

www.autozone.com/.../Hyundai.../Specifications/Torque-Speci...

AutoZoneTorque Specifications. Print. Specific to: Hyundai ... Specific to: Hyundai Accent2006. Hyundai Azera 2006. Hyundai Elantra 2006. Hyundai Sonata 2006.

Club Accent Qu?bec • Consulter le sujet - hyundai motor s

cylinder head bolt torque

52-55 ft lbs. cold engine
59-63 ft lbs. hot engine

connecting rod cap nut 26-28 ft lbs. SOHC
connecting rod cap nut 23-26 ft lbs. DOHC

main caps 41-44 ft lbs.

this sensor is located on the rear of the cylinderhead, next to ignition coil, heres a picture of the camshaft sensor.

Click on the following: direct, FREE Link. It has the diagrams for the Timing Marks you need.
http://www.2carpros.com/car_repair_information/year/2000/make/hyundai/model/accent/2000_hyundai_accent_timing_belt_diagram_marks.htm

Let me know if this helped.

1.5L cylinder head bolt torque

step 1 18 ft lbs.

step 2 60 degrees

step 3 additional 60 degrees

1.6L cylinder head bolt torque

step 1 26 ft lbs.

step 2 90 degrees

step 3 additional 90 degrees

If the valve seal is leaking, the chances are that the valve guides will need to be replaced, maybe not now but soon so you might as well do both. If the valve stems are OK it would pay to reface the valves as well. This will require removing the cylinder head and an engineering works can do the work for you as the seals need to be pressed out and the new ones pressed in again and the head will need to be skimmed.

Hey..my name is Keith..i'll try to answer your question..and the way to find TDC is to take your valve cover off..and find the valves and rocker arms to your #1 cyclinder..then ya rotate the crank til the markings on the harmonic balancer says its at TDC...then you grab the rocker arms on the valves..and if the intake valve and exhaust valve has no pressure on it..then you know you are on #1 cyclinder at TDC..if not..keep rotating the crankshaft until the #1 cyclinder valves has no pressure on them..i hope this has helped

Possibly coils check compression make sure the plugs are the proper ones some engines are particuler about the plugs