Need to adjust the fan belts - 1991 Nissan Maxima

Hi there , there should be a adjuster on the alternator, unless it's a serpentine belt, if a serpentine belt then you will need a new tension bled idler, hope this helps.

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

ARE YOU TALKING ABOUT THE FAN BELT? IF YOU ARE THEN YOU NEED TO ADJUST THE TENSIONER. WHICH WILL ADJUST YOUR FAN BELT AUTOMATICALLY

Hi there:

Check this information...

Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks

1. Align marks on camshaft pulleys with alignment marks on seal plate.
2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
3. Loosen tensioner lock bolt.
4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)

1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
2. Timing Belt Installation
   

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Apply tension to the belt until it is snug and has a live spring action when stuck with the hand dead center. For a more accurate deflection measure the distance from pulley to pulley and use 1/64th inch deflection per inch of belt length. For instance a 32" belt would require a deflection of 32/64" or 1/2". But saying all this I am confused. Your 1995 Corsica does not have a fan belt. The fan is electric. You car also has a serpentine belt which is self tensioning and not adjustable.

Timing Belt Removal & Installation SOHC To Remove:

1. Disconnect battery negative cable.
2. Remove fresh air duct.
3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
4. Remove upper radiator hose.
5. Remove fan clutch assembly bolts.
6. Remove 5 cooling fan shroud bolts.
7. Remove fan shroud and fan as an assembly.
8. Loosen alternator mounting bolts and remove drive belt from pulley.
9. Remove fan pulley.
10. Remove 4 cooling fan assembly bolts.
11. Remove cooling fan assembly.
12. Remove 4 bolts and upper timing belt cover.
13. Remove 2 lower bolts and lower timing belt cover.
14. Loosen adjusting bolt and remove A/C belt.
15. Remove alternator belt.
16. Loosen power steering pump lock bolt and mounting bolt.
17. Remove drive belt from crankshaft damper. Camshaft timing marks
    
    
18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
19. Remove 5 bolts and remove damper.
20. Remove timing belt guide from timing belt pulley.
21. Loosen tensioner lock bolt.
22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
    
23. Remove timing belt.

To Install:
Timing belt pulley timing marks

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation

1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
   Do not turn crankshaft counterclockwise.
   
3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
   • Deflection should measure 0.43-0.51 inch (11-13 mm)
   NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
   
6. Install timing belt guide.
7. Install crankshaft damper pulley.
8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
9. Install power steering pump drive belt.
10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
11. Install alternator drive belt.
12. Install A/C drive belt.
13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
16. Install fan pulley.
17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
19. Adjust alternator belt tension and tighten alternator mounting bolts.
20. Install upper radiator hose.
21. Install fresh air duct.
22. Connect battery negative cable.
23. Refill/bleed cooling system.

DOHC To Remove:

1. Disconnect battery negative cable.
2. Remove fresh air duct.
3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
4. Remove 4 thermo-modulated fan shroud fasteners.
5. Remove generator drive belt.
6. Remove fan pulley (located above crankshaft pulley).
7. Remove 4 bolts and splash shield (located under front of vehicle).
8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal
   
   
9. Remove 5 bolts and upper timing belt cover.
10. Remove 2 bolts and lower timing belt cover.
11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
    
13. Remove timing belt.

To Install:
Crankshaft match marks

1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks
   
   
2. Align marks on camshaft pulleys with alignment marks on seal plate.
3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
4. Loosen tensioner lock bolt.
5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
   • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
   NOTE: Replace tensioner spring if timing belt deflection is excessive.
   Timing Belt Installation
   
   
8. Install lower timing belt cover.
9. Install upper timing belt cover.
10. Install power steering drive belt and adjust belt tension.
11. Install fan pulley.
12. Install generator drive belt and adjust belt tension.
13. Install A/C drive belt and adjust belt tension.
14. Install splash guard.
15. Install fan and fan shroud.
16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
17. Install fan shroud mounting bolts.
18. Install fresh air duct.
19. Connect hose to resonance chamber.
20. Connect battery negative cable.

serpentine belts dont need adjusting they have a tensioner pulley that is spring loaded / you may need a new tensioner pulley or belt . hope that helps

Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks

1. Align marks on camshaft pulleys with alignment marks on seal plate.
2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
3. Loosen tensioner lock bolt.
4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
8. NOTE: Replace tensioner spring if timing belt deflection is excessive.

Timing Belt Installation

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

go to toyota buy a fan belt, i think u can see a belt adjuster need the belt and engine , you just need to adjust the belt to very good tension

first of all you need to find the power steering adjuster you will find this beside power steering pump there is a locking nut on pulley slacken that then slacken off adjusters once you have done that you will be able to remove belt same applies for slackening alt belt make sure you slacken of locking bolt otherwise you will bend adjuster bolt.hope this helps you.