How do you install an inside door handle on a 1997 GMC Sierra?

Search Results

How To Install Replace Inside Door Handle Chevy Equinox ...

? 9:02
https://www.youtube.com/watch?v=cY6asyM2R6g
Feb 2, 2012 - Uploaded by 1A Auto Parts
How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

How To Install Replace Inside Door Handle 2007-13 ...

? 9:05
https://www.youtube.com/watch?v=QonKLwhk2CE
Apr 2, 2015 - Uploaded by 1A Auto Parts
http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

How To Install Remove Rear Outside Door Handle 2007-13 ...

? 10:02
https://www.youtube.com/watch?v=7ZUTqqEzpZg

Very common problem with these trucks. The inside door handle needs to be replaced. They do sell after market handles for these trucks but i would pay the difference and get an OE handle from the GM dealership. There isnt much of a difference in price and a huge difference in quality:)

I've got a 97 GMC Yukon XL, I have a problem with the inside door handle on the driver side. To open the door I have to pull the handle and give it a shoulder for it to open. I think my problem is my door latch, I think it's giving out? Help

see if you can pull the outside handle out a little & put some needlenose pliers in the opening & grab the rod to open the door. otherwise unscrew the door panel & get into the inside of the door that way.

good luck

try puting key in lock first and tun it fast back and forward as u raise the door handle like u was tring to open the door

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Remove the clips and screws securing the old window to the arm and slide it out through the top of the door (may need to be maneuvered out)

Broken inside door handles are a common problem and there is not an easier way of fixing problem.drill out head of rivet with a 3/16 drill bit.Then slide handle assy. from panel.To install new handle attach the two rods you removed .Then slide new handle back into the slots and replace the rivet.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008f768
Hope this helps!

The door panel is held onto the door with clips but first you need to remove the screws from the grab handle on the door panel. then pop the bezel off around the inside door handle. very carefully!!! then using a clip tool pry off the peice that covers the rear view mirror nuts and pry gently all the way around the door panel until its loose then lift it up slightly to unseat the window channel strip off the door, then unhook your wires. As for the window roll it up, tape it to the door then line up the 2 10mm bolts that clamp it to the regulator with the provided holes in the door, loosen 'em up roll the regulator down and remove the window. Have fun guys!!!

no matter what you do door panel has to come of if it is a two piece top and bottom better for you once it is off make sure window is up all the way disconnect handle rod most are held on with a lock clip from one of access holes in top of door then remove two mounting nuts on the handle bolts that come from the outside to the in the vhandle should come right out then have someone on the outside install handle threw door will you reinstall the two nuts on the threaded bolts on the inside reinstall rod to handle then door panel your done