Need to change the factory keyless entry code OR the module

I'm not sure what you mean by "reset" the keyless entry.I am guessing you are wanting to erase a personal code that has been programed into the keyless entry. The factory code (the code that came with the vehicle) is always there and cannot be changed. If remiving the personal code is what you are looking to do, punch in the factory code that came with the vehicle then after the factory code is entered simply push the 1/2 button within 5 seconds and reliese. This will clear the personal code made and now only the factory code will work. If you want to after you push the 1/2 button you can enter a new personal code. after you push in the new personal code the locks will cycle once to confirm that the new code has been programed and this will also erase any prior personal codes programed into the vehicle. I hope this was what you were needing and I hope it helped. Good luck.

this code is located on a module on inside left rear panel where your car jack is located you will need a flashlight to look up on the module there will be a sticker on this module with 5 digits this will be the original factory code to lock or unlock your car . inside your owners manual there is a procedure to change the code .

door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:

1. Enter the factory set five-digit code (the keypad will illuminate when pressed).

1. Press 1/2 within five seconds of Step 1.

1. Enter the unique five-digit code.

The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:

1. Enter factory set five-digit code.

1. Press 1/2 within five seconds of Step 1.

1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.

The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:

• one minute of keypad inactivity
• the keyless entry remote transmitter UNLOCK button is pressed
• the ignition is turned to the ON position.

Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification

1. Verify the customer concern by operating the system.

1. Visually inspect for obvious signs of mechanical or electrical damage.

You must have the original code to change it, if u do here is how you do it.
KEYLESS ENTRY SYSTEM
With the keyless entry keypad, you can:
• lock or unlock the vehicle doors without using the key,
• release the liftgate glass,
• enable or disable the autolock function, and
• add or delete a 5–digit personal user code.
Your vehicle has a factory set 5–digit code that operates the keyless
entry system. You can also program your own 5–digit personal entry
code. The factory-set code is located:
• on the owner’s wallet card in the glove compartment,
• at your dealer,
• or on the module located under
the right-hand side of the
instrument panel, adjacent to the
passenger compartment fuse
panel.
Note: The 5–digit code (e.g. 12345)
will be in large, BOLD numbers on
the module label.
When pressing the controls on the keyless entry keypad, press the
middle of the controls to ensure a good activation.
Programming your own personal entry code
To program your own code:
6. Enter the factory set code (keypad will illuminate when pressed).
7. Press the 1 • 2 control within five seconds of Step 1.
8. Enter your personal 5–digit code.
Enter each digit within five seconds
of previous one.
9. After the code is entered, the
locks will cycle, confirming that the
new code has been set.
Do not set a code that includes five of the same number or presents
them in sequential order. Thieves can easily figure out these types of
codes.
Your personal code does not replace the permanent code that the
dealership gave you. You can use either code to unlock your vehicle. If a
second personal code is entered, the module will erase the first personal
code in favor of the new code.
If you wish to erase your personal code, use the following instructions:
1. Enter the factory set code.
2. Press the 1 • 2 control and release.
The system will now only respond to the factory set code.

there is no such thing as a universal factory keyless code, what are u doing here? the code is printed on a tag on the keyless entry module, that code is unique to every van and the module in stalled on it, there are 100's of different codes.

1. Enter the five digit permanent entry code into keyless entry keypad.
2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
   • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code: 9/0-- no memory recall
     1/2-- memory seat position 1
     314-- memory seat position 2
     5/6-- memory seat position 3
     
   • After successful programming, the doors will signal by locking and then unlocking.
   
   

The Keyless Entry Module is located inside the drivers side door.

if you do not already know the factory code, the only way it can be obtained is by your local ford dealer. the proprietary computer equiptment they have can access the code that is programed in vehicles security module. if you purchased it used..it is often that the keyless entry code id card is still withe the owners manual..it is a 5 digit code printed on an credit card sized card that is white in color..i hope this helps you...good luck

Bill look under dash on drivers side find the keyless entry module, the bold numbers on the module are your factory keyless code, hope this helps

your factory code for keyless entry by number pad? this is found on the module for keyless entry located under dash left side, number on module in BOLD type is the original or factory code

factory keyless entry codes are the bold 5 digit number located on the keyless entry control module, the module is usually located on the drivers side above the parking brake handle