Question about 1996 Mitsubishi Eclipse

1 Answer

Wire harness change on Mitsubishi Eclipse

I need to change out the positive wire harness on my 98 mitsubishi eclipse(4 cyl. 2.0 ltr. no turbo). Would like to do it myself but have never done it before. I would like a guide or a fuse and wiring diagram to do it myself. I'm more of an old school mechanic and all these electrical wires got me scratching my head.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Mitsubishi Master
  • 364 Answers

Here is the factory electrical manual. It should have everything you need. (Mitsubishi has the best electrical manual i have ever seen)

97 99Electrical pdf

Posted on Dec 28, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 85178 Answers

SOURCE: what kind of oil goes to mitsubishi eclipse rs 2002

any major brand (like Pennsoil) 10W-30W

Posted on Apr 30, 2009

  • 31 Answers

SOURCE: How do you adjust idle on 2001 mitsubishi eclipse,

idle should be self ajusting might check for vacum hoses off if not idleing proper

Posted on May 15, 2009

  • 35 Answers

SOURCE: brake light bulb Mitsubishi Eclipse Cars

look for access panels in rear hatch there will be one on each side remove those and there will be 10 ml nuts holding the light housings on remove those then you can access the lights

Posted on Jul 02, 2009

bschilz
  • 2049 Answers

SOURCE: Location of thermostat 2003 Mitsubetsi Eclipse 4

The thermostat is found at the end of the top radiator hose . Find the top radiator hose and follow it to the engine .There you will find a thermostat housing with the end of the hose attached . There will be 2 bolts holding down the housing to the engine. Undo the bolts and pull the housing off and the thermostat will be there.

Posted on Sep 06, 2009

sk8rdude_88
  • 27 Answers

SOURCE: need the vacuum hose diagram for a 1998 mitsubishi eclipse

http://www.dsmtuners.com/forums/attachments/420a-bolt-tech/89827d1228187918-resolved-need-vacuum-line-help-fast-420aturbovac-boostlinesstock.jpg
hope this helps

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where are the timing marks on a 1996 Mitsubishi eclipse?


If you have the 4-Cylinder Non-Turbo, or 420a engine, here is the overhaul manual for it, including the complete timing instructions: http://www.mediafire.com/?7j2zosdmnnl

If you have the 4-Cylinder Turbo, or 4G63 engine, here is the manual for it, including timing instructions: http://www.mediafire.com/?zhnttihoqye

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Mar 18, 2011 | 1996 Mitsubishi Eclipse

1 Answer

I have 98 eclipse non turbo and stick shift and the battery light keeps coming on and i have changed the alternator and battery


computer needs to reset . Disconnect battery and leave alone for no less than 1 hr. If problem persists , Check your belt tension or connections to the alternator

Aug 11, 2010 | 1998 Mitsubishi Eclipse

2 Answers

How install the timming belt in my mitsubishi eclipse gst turbo 98


this link has a step-by-step DIY for changing the timing belt on your car. 2G TURBO TIMING BELT PROCEDURE

Jun 20, 2010 | 1998 Mitsubishi Eclipse

1 Answer

Change the engine computer


before i start to explain how to replace this i cant stress this enough MAKE SURE THAT IS THE RIGHT COMPUTER FOR THAT ECLIPSE. the 95 non turbo eclipse has a different computer from the 96 to 99. and the gst and the gsx computers are different from eachother. the gst and the gsx computers are also different from the 95 and the 96-99 non turbo eclipses. when you get the computer i would bring your vin number to any local parts store or the dealer and they should know what to do with it. now that that is said. which computer do you need replaced. if your talking about the one inside the car it is located under the center console right behind the e-brake. removing that can be a challenge due to the several bolts that holds it on. you can use a phillips head screw driver but i wouldnt recommend it. i believe it is a 10mm socket that they will fix. after you get that off i would disconnect your battery. wait a few minutes than ground yourself out to the bracket holding the shift bar on(just grab ahold of it) after that is said and done there should be 4 bolts holding it on. (i believe 10mm cant remember) and a clip with several wires going to it. before installing. clean up the area around where the computer sat. remove any dirt or anything that may be there. check the clip that plugs into it for any damage, broken or burn wires, or if the plastic clip in itself is damaged. if not the dealer would be the only place to replace this at and i would strongly recommend a garage putting it in. if all is good installation is the opposite of removal. after you get everything together turn the car to the on possition with out starting the motor and let it sit for about 10 min. this will allow that computer to learn the way your car is set up. after that you should be able to start the motor with out a problem.
if you want the computer under the hood than its simple disconnect 1 or 2 clips and 3 to 4 bolts holding it on. inspect everything before installing the new computer along with cleaning up and dirt or rust in the area. and do the same process i explained about the other computer

Oct 05, 2009 | 1998 Mitsubishi Eclipse

3 Answers

Put new plug wires on my eclipse now it runs crappy


You may have your plug wires in the wrong order.
The firing order is 1-3-4-2 om cpounter-clockwise rotation. Look at the digram below. Notice the shaded blue is cylinder 1. From there, make sure 3 is the next wire, then 4 and finally 2.


1f9ac8c.gif

Oct 03, 2009 | 1995 Mitsubishi Eclipse

3 Answers

Crankshaft position sensor location


Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Mar 10, 2009 | 1995 Mitsubishi Eclipse

3 Answers

Wanting to go bigger engine!


if you swap in the turbo 2.0 4g63 your gonna need a turbo trans. the non-turbo wont work and he motor mounts should bolt up the same..hope this helps

Jan 21, 2009 | 1991 Mitsubishi Eclipse

1 Answer

Head gasket install how?


get a haynes manual at local auto parts store

Dec 18, 2008 | 1999 Mitsubishi Eclipse

Not finding what you are looking for?
1996 Mitsubishi Eclipse Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...