How to assemble trim rider Bollinger and set it for use?

Preliminary Procedures
Remove the rear seat. Refer to Rear Seat Replacement.
Remove the left quarter lower trim panel. Refer to Quarter Lower Rear Trim Panel Replacement.


Preliminary Procedure
Remove the rear compartment floor stowage compartment tray. Refer to Rear Floor Trim Plate Replacement.
1
Rear Seat Nut (Qty: 6)
Caution: Refer to Fastener Caution in the Preface section.
Tip
Roll the seat forward enough to get access to the nut that attaches the center seat belt assembly to the floor.
Tighten
45 N·m (33 lb ft)
2
Rear Seat Bolt (Qty: 3)
Tip
• Adjust the seat forward or rearward to access the bolts.
• Remove the plastic trim pieces to gain access to the nuts.
Tighten
45 N·m (33 lb ft)
3
Rear Seat Assembly

Preliminary Procedures
Remove the quarter upper trim finish panel. Refer to Quarter Upper Trim Panel Replacement.
Remove the rear compartment trim panel. Refer to Rear Compartment Trim Panel Replacement.
Remove the floor trim plate. Refer to Rear Floor Trim Plate Replacement.
1
Quarter Lower Trim Finish Retainer (Qty: 2)
2
Quarter Lower Trim Finish Panel Assembly
Caution: Refer to Fastener Caution in the Preface section.
Procedure
Remove the cargo tie down loop anchor plates and bolts.
Remove the rear passenger seat belt guide.
Disconnect the rear passenger seat belt so that the trim panel can be removed around the seat belt. Refer to Rear Seat Belt Replacement.
Pull the trim panel toward the inside of the vehicle to disengage the retainers.
Tighten
9 N·m (80 lb in)
3
Quarter Lower Trim Finish Panel Retainer (Qty: 5)

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Yes it can be reset, but you must remove the seat trim and cover, Then disconnect the power drive and then set the adjustment where you want it, reconnect the power drive and reinstall the trim and the seat covers.

Parking aid speaker attached to the parking aid module.

1. Remove the RH quarter trim panel. For additional information, refer to Section 501-05 .

1. Disconnect the parking aid module electrical connector

1. Remove the bolt and the parking aid module.

1. To install, reverse the removal procedure



2. The parking aid system is disabled if a fault is detected in one of the 4 sensors, the parking aid speaker, or the parking aid module. This is indicated by the parking aid disabled warning. The parking aid module is on the international standards organization (ISO) 9141 network and can be diagnosed with a diagnostic tool.



3. 
   Rear Quarter Trim Panel
   
   Removal and Installation
   
   
   
   All vehicles
   
   
   
   
   
   
   1. Remove the rear door scuff plate.
   
   
   
   
   
   
   
   
   1. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel in this section.
   
   
   
   
   
   
   
   
   1. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section.
   
   
   
   
   
   
   
   
   1. Remove the liftgate scuff plate trim panel.
   
   
   
   
   Vehicles with third row seating
   
   
   
   
   
   
   1. Remove the third row seat. For additional information, refer to Section 501-10 .
   
   
   
   
   
   
   
   
   1. Position the liftgate opening weatherstrip aside.
   
   
   
   
   All vehicles
   
   
   
   
   
   
   1. If equipped, remove the luggage assembly cover.
   
   
   
   
   
   
   
   
   1. Remove the stowage compartment doors.
   
   
   
   
   
   
   
   
   1. NOTE: RH side shown, LH side similar.
      
      
      Remove the stowage compartment assembly.
   
   
   
   
   
   
   
   
   1. Position the carpet aside.
   
   
   
   
   
   
   
   
   1. Remove the brackets.
      
      
      
      
      
      • Remove the bolts.
      
      
      
      
   
   
   
   
   
   
   
   
   1. Remove the rear quarter trim panel.
      
   
   

Well, this good to be interesting to say the least, and probably long as well. By my gm. service information your going to need to take out the front bucket seats so the sides of the console can come off.


Remove the left front seat . Refer to Bucket Seat Replacement .



1



Front Floor Console Extension Panel



2



Retainer Clip (Qty: 5) same for right side.


















Callout







Component Name






Preliminary Procedure

Remove the right front seat. Refer to Bucket Seat Replacement .







1





Front Floor Console Extension Panel







2





Retainer Clip (Qty: 5)








Front Floor Console Accessory Trim Plate Assembly


Procedure

Use a flat bladed plastic trim tool in order to release the console accessory trim plate from the console assembly.



2



Retainer Clips (Qty: 5)



Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement.



1



Front Floor Console Accessory Housing Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Accessory Housing Assembly


Procedure

1. Disconnect the electrical connectors.



2. When replacing the front floor console accessory housing assembly, transfer all necessary components

1. Remove the rght or left front floor console extension panel. Refer to Front Floor Console Extension Panel Replacement - Right Side or Front Floor Console Extension Panel Replacement - Left Side .



2. Remove the front floor console cup holder housing. Refer to Front Floor Console Cup Holder Housing Replacement .

1



Front Floor Console Rear Trim Panel Screw (Qty: 1)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Rear Trim Panel



3



Retainer Clip (Qty: 4)


Preliminary Procedures

1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .



2. Remove the right and left front floor console fillers. Refer to Front Floor Console Filler Replacement .

1



Front Floor Console Armrest Assembly Bolt (Qty: 4)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

9 N?·m (80 lb in)



2



Front Floor Console Armrest Assembly


Procedure

Position the armrest assembly out of the way leaving the electrical harness attached.



3



Front Floor Upper Console Trim Plate


Procedure

Lift the rear of the trim plate first, releasing the retainers securing the trip plate to the console assembly.



4



Retainer Clips (Qty: 4)



Front Floor Console Replacement (Enclave)




















Callout







Component Name






Preliminary Procedures

1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .



2. Remove the right and left front floor console extension panels. Refer to Front Floor Console Extension Panel Replacement - Right Side and Front Floor Console Extension Panel Replacement - Left Side .



3. Disconnect the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Replacement .

1





Front Floor Console Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)







2





Front Floor Console Bolt (Qty: 10)




Tip

Before installing the right lower forward bolt, ensure that the console wiring harness is tucked below the fastener location to avoid driving the bolt into the harness.




Tighten

9 N?·m (80 lb in)







3





Front Floor Console Assembly


Procedure

1. Note location and routing of the front floor console wiring harness prior to removal of the front floor console assembly to ensure proper reinstallation.



2. Disconnect the electrical connectors.



3. With the aid of an assistant remove the console assembly from the vehicle.



4. When replacing the front floor console, transfer all necessary components.
   

1. Open cup holder and remove (2) Phillips 7mm screws.

2. Unsnap and remove power outlet assembly from lower storage, unplug power outlet wires and put assembly in a safe location.

3. Open lower storage door and remove (2) 7mm screws inside.

4. Models with DVD - Remove DVD player and remove (2) 7mm screws from behind and (2) 7mm screws near the floor.

5. Remove lower storage compartment, put it in a safe location.

6. Remove (2) 7mm screws (facing up) from the cup holder.

7.Remove (3) 7mm screws and remove radio.

The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass

1. Close the sunroof and open the sunshade.
2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
4. Remove the glass from the vehicle.
   

To install:

1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
4. Check the operation and fit of the glass.
   

Motor

1. Disconnect the negative battery cable.
2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
3. Remove the headlines as follows:
   1. If equipped, remove the overhead or sunroof console.
   2. If equipped, remove the dome lamp.
   3. Remove the coat hooks and the assist handles.
   4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
   5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
   6. On four door models, remove the body lock pillar trim panels.
   7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
   8. On two door models, remove the rear seat upper seat belt anchor bolts.
   9. Remove the upper and lower front seat belt anchor bolts.
   10. Remove the rear seat belt lower anchor nut (two door models only).
   11. Remove the end gate or liftgate opening sill plate.
   12. Remove the jack storage cover (left side).
   13. Remove the upper body side trim panel screw (left side).
   14. Remove the upper body side trim panel and the body side front lower trim panel.
   15. Remove the headliner from the vehicle.
4. Remove the sunroof console mounting bracket.
5. Remove the straps that retain the wiring harness.
6. Tag and unplug any necessary electrical connections.
7. Unfasten the screws that attach the motor to the sunroof assembly.
8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
   

To install:

1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
2. Attach all electrical connections that were unplugged.
3. Attach the straps that retain the wiring harness.
4. Install the sunroof console mounting bracket.
   

New headliners must be pierced to accommodate actual vehicle accessories.

1. Install the headliner as follows:
   1. Install the body side front lower trim panel and the upper body side trim panel.
   2. Install the upper body side trim panel screw (left side).
   3. Install the jack storage cover (left side).
   4. Install the end gate or liftgate opening sill plate.
   5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
   6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
   7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
   8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
   9. On four door models, install the body lock pillar trim panels.
   10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
   11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
   12. Install the coat hooks and the assist handles.
   13. If equipped, install the dome lamp.
   14. If equipped, install the overhead or sunroof console.
       
2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.

• Ignition Removal Instructions
  
• Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}

• Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .

• Put the key in the steering column lock cylinder set (1).

• Turn the key to the "START" position.

• Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.

• Turn the steering column lock cylinder set (1) into the "RUN" position.

• Pull the steering column lock cylinder set (1) out from the lock module assembly.

• Remove the key from the steering column lock cylinder set (1).
  

• Installation Instructions

Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}

• Insert the key into the steering column lock cylinder set (1).
• LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
• Push the steering column lock cylinder set (1) into the lock module assembly (6).
• Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
• Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
• Remove the ignition key from the lock cylinder set (1).
• Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

I hope this helps and good luck.
Please remember to vote and leave a testimonial. Thanks.

PLEASE DON'T FORGET TO RATE!!!

Signal & Marker Lights Removal & Installation Rear Lamp Assembly Sedan To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove the luggage compartment quarter trim panels.
3. Disconnect the rear lamp assembly electrical connector.
4. Remove the lamp assembly mounting nuts.
5. Pull the lamp assembly away from the body.
6. Disconnect the rear lamp assembly bulb connectors.
7. Remove the rear lamp assembly.

To Install:
CAUTION
To prevent water from entering the luggage compartment, make sure the rubber grommet is fully seated.

1. Position the rear lamp assembly near the body and connect the bulb connectors.
2. Install the lamp assembly into the body.
3. Install the lamp assembly mounting nuts. Tighten to 53 in-lbs (6 Nm).
4. Connect the rear lamp assembly electrical connector.
5. Install the luggage compartment quarter trim panels.

the gear broke or the bar inside is broken,take it to a body shop and have them dis -assemble the covering on the rear of the seat then you can see the problem