Can't find headlight adjustment screws

A screwdriver, but you need the target board that garages have. From a certain distance on flat ground, the beam has to hit the board in a certain way.

https://www.cargurus.com/Cars/Discussion-t66940_ds1068808

Get flat screwdriver and star screwdriver

menu

How to Adjust a Headlamp Beam on a 2005 Chevrolet Cavalier...

When you replace the headlamp assembly in the 2005 Chevrolet Cavalier, you must also adjust the headlamp beams. Like most vehicles, there are two screws located on the headlamp assembly that control the vertical and horizontal direction of the headlamps. Proper adjustment is necessary for adequate visibility during nighttime driving; bad adjustment can make it difficult for you to see or make it difficult for oncoming drivers to see, creating a potentially dangerous situation. You can adjust the headlamp beams yourself with a screwdriver in about 15 minutes.
Park the Chevrolet Cavalier on a flat surface facing a wall or garage door approximately 15 feet away. Park the Car so that it is perpendicular to the wall.

Lift the hood and remove the plastic trim panel above each of the headlights. There are three plastic fasteners that secure the trim panel; pry the fasteners out using a flathead screwdriver. Lift the trim panel up to remove. There are two adjusting screws beneath the trim panel, one on the top of the headlamp assembly and one along the outer side of the headlamp assembly.

Turn the headlights on so that they shine on the wall. Ensure the headlights are on the "dim" setting.

Adjust the vertical bolt, located on the top of the headlight assembly near the center of the vehicle to raise or lower the headlight, using a crosspoint screwdriver. Turn the screw counterclockwise to lower the headlamp beam; turn the screw clockwise to raise the headlamp beam. Adjust the headlamp so that the beam is below a driver's eye level.

Adjust the horizontal bolt, located on the outer side of the headlamp assembly to move the headlamp beam right of left, using a crosspoint screwdriver. Turn the screw counterclockwise to move the headlamp beam right; turn the screw clockwise to turn the beam left. Adjust the headlamp so that the beam shines straight ahead or slightly toward the center of the vehicle.

Replace the plastic trim panel and fasteners and close the hood. Warning: raising the lights too high can make it difficult for other drivers to see you.

If you dont have the proper tool to do it,wait for the night come,locate on the top of each side of the eadlights the scrwes where you can adjus them,in a flat ground adjust the lighst.

if the adjusters are sticking spray them with wd40 or give them a wiggle after loosening the screws....poss just rusty...

no its not possible most newer cars like 05's and older have a automatic relay so when ignition is off they automatically shut off so you dont forget about them and drain your battery

thats it my freind one on each side/Plaes rate my response thank you very much

its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

hello wwhampton,

open the hood, take a close look at your headlights, if it is a headlight assembly, there are two screws with big plastic heads on the back of the assembly, these are the adjusting screws. one for horizontal adjustment and the other one is for vertical adjustment.

if the headlight is a round or square ordinary bulb, the adjusting screws are located near the bulb itself, these are philips screws. one on the top and one on the side.

a suggestion; when adjusting headlights, face the car to a wall about 5 ft away and adjust the headlight.

tnx 4 using fixya.

drcool