Keyless remote locks the doors but the horn doesn't honk.

To arm content theft alarm.
1. Open the door.
2. Lock the door with the power door lock switch or
the remote keyless entry transmitter. The
SECURITY light should flash.
3. Close all doors. The SECURITY light should go off
after approximately 30 seconds. The alarm is not
armed until the SECURITY light goes off.

If a locked door is opened without the key or the remote keyless entry transmitter, the alarm will go off. The headlamps and parking lamps will flash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power.

Does it have keyless entry ?
Power Door Locks
The central security module controls the power door lock and keyless entry system. The lock and unlock operation is carried out by supplying ground to the central security module from the door lock control switch. The normal path of the actuators is to ground through the central security module. The door lock control switch will lock and unlock all doors by grounding the appropriate circuit to the central security module. The central security module then supplies power to the appropriate common actuator circuit to lock or unlock all doors.

Keyless Entry
The keyless entry remote transmitter sends a frequency that is received by the central security module internal antenna. Depending on the frequency received, the central security module will lock all doors or unlock the driver door. If the unlock frequency is received again within five seconds of the first unlock, the central security module will unlock all doors.
If the frequency received is from the panic button, the central security module will cycle ground to the parking lamps and horn. The parking lamps and horn will continue to cycle until the panic button is pressed again or the ignition switch is turned to the RUN position.

System Description
The horn system consists of the following components:
?€¢
HORN fuse

?€¢
Horn relay

?€¢
Horn slip ring

?€¢
Horn switch

?€¢
Horn assembly

?€¢
Body Control Module (BCM)

System Operation
The vehicle horn system is activated under the following conditions:
?€¢
The horn switch is depressed.

?€¢
The body control module (BCM) commands the horns on. The BCM commands the horns on under any of the following conditions:

-
When the panic button is depressed on the remote control door lock transmitter. For further information refer to Keyless Entry System Description and Operation .

-
When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization. For further information refer to Keyless Entry System Description and Operation .

If your vehicle is equipped with a factory keyless entry system and you have the owner's manual, there should be a section in the manual describing how to change your options with your system. But if you have an aftermarket system, which I am thinking this the case, you will have to manually go into your dash under your steering wheel and cut the wire going to your horn from the security system. Once you have accessed your wiring underneath your steering wheel, there is a main harness with a bunch of wires going to the steering wheel. In this harness you will find a DARK GREEN/VIOLET small gauge wire and you should see another wire tapping into it probably coming from the security module. Just cut it off but leave the DARK GREEN/VIOLET untouched and this will eliminate the horn honks.

I have a 2004 Dodge Durango. When I push the lock button it will lock door and set the alarm but the horn does not blow this is normal on my car. As Dodge is apart of Chrysler maybe it's the same for you, Unless in the past it did trigger the horn then the only thing I can think of is maybe there are different setting for your car. Check the owners manual. Hope this helps.

IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

If you have your owner's manual, there is a section that will tell you the exact sequence to press to enable/disable the horn bonk. It has three settings, chirp, honk, and off. The chirp is a really quick chirp of the horn. Honk is a longer honk. Off seems to be what you've set.

I hope this helps.

Look in your manuel, there are steps to change the Key less remote setting to customize it the way you'ld like the car Key less system to work.
Good luck and hope this helps, if your still having problem. Just drive the Dodge dealer and ask the Service adviser to help you out, he or she would be more then happy to reprogram the key less system for you.

there are two seperate horns

If you look in the jeeps owners manual for the keyless remote section, you can program the horn to honk or not honk when you lock the doors.