On my 1991f-250, 2 wheel drive,automatic with the 460efi motor,why does it take so long to shift?

There are a few potential issues that could be causing your 2004 GMC Envoy SLT to go into 4-low but not 4-high or 2-wheel drive. Some possible causes include:

1. Transfer case issues: The transfer case is responsible for controlling the engagement of the different drive modes. If the transfer case is damaged or malfunctioning, it may not be able to engage 4-high or 2-wheel drive.
2. Shift motor issues: The shift motor is responsible for controlling the engagement of the transfer case. If the shift motor is damaged or malfunctioning, it may not be able to engage 4-high or 2-wheel drive.
3. Vacuum issues: The vacuum system is responsible for controlling the engagement of the transfer case. If there is a problem with the vacuum system, it may not be able to engage 4-high or 2-wheel drive.
4. Wiring issues: The wiring that controls the transfer case and shift motor can become damaged or corroded over time. This can cause the transfer case to not engage 4-high or 2-wheel drive.
5. Control module issues: The control module that controls the transfer case and shift motor can fail. This can cause the transfer case to not engage 4-high or 2-wheel drive.

It's best to diagnose the issue by a professional mechanic, who can perform a proper diagnosis and repair the issue. They will be able to determine the specific cause of the problem and recommend the appropriate repairs.

Which of these does your vehicle have ?

Transfer Case - NVG 233-NP1 (Two Speed Selectable)
Transfer Case - NVG 136-NP4(One Speed Automatic)

The New Venture Gear NV233 is an electronic shift transfer, with the following three modes of operation, Two-wheel drive high range, Four-wheel drive high range, Four-wheel drive low range. The gear reduction for low range is provided by a planetary gear set. The floor-mounted shifter has been eliminated. A switch, located on the upper right side of the instrument panel, is used to select the operating range. The indicator lamps on the switch show the current mode of operation. When the four-wheel drive has been selected, the four-wheel drive indicator lamp on the switch is designed to turn on when the front axle has engaged.


Automatic Transfer Case
The single speed automatic transfer case system shifts automatically from rear wheel drive to four wheel drive when the transfer case shift control module (TCSCM) senses the difference in rotation speed of the front propeller shaft and the rear propeller shaft . Two vehicle speed sensors, one located at the rear output shaft area of the transfer case, and the other, located at the front output shaft area of the transfer case, send front and rear propeller shaft rotation speed information to the TCSCM.
When the front and rear output shaft rotations remain the same, the TCSCM sends pulse width modulation signals to the encoder/motor to keep the transfer case in rear wheel drive. When the front and rear output shafts rotations are different, the shift control module sends pulse width modulation signals to the encoder/motor to engage the transfer case into four wheel drive.
The system will automatically transfer a percentage of torque to either the front or rear axles as required to stop all wheel slip. When the front and rear output shafts rotations return to the same speed rotation, the shift control module sends pulse width modulation signals to the encoder/motor to position the transfer case back into rear wheel drive.
When the transfer case is engaged into four wheel drive, a lamp indicator on the instrument cluster will light. The automatic transfer case system is completely automated, no transfer case control button switching system is required.

Do you know what diagnostic trouble code's are ?

DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error
DTC C0895 Device Voltage Malfunction

Not OBD2 engine code's .

Which do you have ?
Transfer Case - NVG 236 (Two Speed Automatic)
Transfer Case - NVG 233-NP1 (Two Speed Selectable)
The NV236 transfer case is an automatic transfer case with three drive ranges. Shifting from rear wheel drive to four wheel drive is done automatically when the transfer case shift control module receives wheel rotating slip information from the speed sensors. The transfer case shift control module then engages the transfer case motor/encoder to position the transfer case from rear to four wheel drive. When the transfer case shift control module receives information that the wheel rotation is the same on both axles, the transfer case shift control module sends position information to the motor/encoder to put the transfer case back into rear wheel drive. The three drive ranges are 2HI, 4HI, and 4LO. The 2HI position is for normal driving with the rear wheels pushing the vehicle. The 4HI, position is for driving through sand, snow, mud, gravel, or heavy rain at normal or slightly below normal speeds. The 4HI engages the front axle to allow for four wheel drive. The front axle is pulling the vehicle, and the rear axle is pushing the vehicle. The 4LO range is used for off road driving, heavy snow, deep mud, or shallow fording. The 4LO is similar to the 4HI except that the gearing in the transfer case is set for low speed and high torque. The NV236 is manufactured at Syracuse New York by New Venture Gear a division of New Process Gear for General Motors.
Is the switch light on or flashing ? If you have automatic 4x4 there are several DTC'S that can set >
DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0362 4LO Discrete Output Circuit High DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error

No 4X4 switch on the instrument panel ?
Automatic Transfer Case
The single speed automatic transfer case system shifts automatically from rear wheel drive to four wheel drive when the transfer case shift control module (TCSCM) senses the difference in rotation speed of the front propeller shaft and the rear propeller shaft . Two vehicle speed sensors, one located at the rear output shaft area of the transfer case, and the other, located at the front output shaft area of the transfer case, send front and rear propeller shaft rotation speed information to the TCSCM.
When the front and rear output shaft rotations remain the same, the TCSCM sends pulse width modulation signals to the encoder/motor to keep the transfer case in rear wheel drive. When the front and rear output shafts rotations are different, the shift control module sends pulse width modulation signals to the encoder/motor to engage the transfer case into four wheel drive.
The system will automatically transfer a percentage of torque to either the front or rear axles as required to stop all wheel slip. When the front and rear output shafts rotations return to the same speed rotation, the shift control module sends pulse width modulation signals to the encoder/motor to position the transfer case back into rear wheel drive.
When the transfer case is engaged into four wheel drive, a lamp indicator on the instrument cluster will light. The automatic transfer case system is completely automated, no transfer case control button switching system is required.

Do you know what DTC'S - diagnostic trouble code's are ?
Auto part stores can't read these , your best bet take it to a qualified repair shop . One that has the knowledge an diagnostic equipment .
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error
DTC C0895 Device Voltage Malfunction
Without proper factory service an repair info. an diagnostic tools

SHIFT MOTOR ON TRANSFER CASE ARE COMMON, ALSO THEY HAVE PROBLEMS WITH THE AUTO LOCK-OUTS ON THE FRONT WHEELS. TRY TAPPING ON SHIFT MOTOR WITH HAMMER WHILE A HELPER PUSHES THE BUTTON.

better still rip it out and put a manual gearbox in

your drive shaft thats turning is mabe broke or your automatic 4x4 lockers could be bad

look on fire wall pass. side you will see 2 parts with vacume lines attached 99 percent of the time that is what went i had the same problem

try putting your truck in neutral and then shifting into 2 wheel drive shift on the fly does not apply to 4 low only 4 high and on electric shift models it wont shift unless your ****** is in neutral.

Check to see if you are getting power through your switch on your dash. I also suspect your shift motor but it is a lot easier to check it with a test light.