Frt. wheel bearings 2003 h-2

Question 1

0helpful

1answer

Dealer replaced driver side frt wheel bearing. When I got home and looked under frt end there is a lot of fluid dripping off center casing car has never leaked adrop before what could have happened

Some driveshafts are retained in the differential by a circlip and can't be disturbed accidentally during a wheel bearing change or other similar work.

Some driveshafts aren't retained and can easily be displaced during a wheel bearing change. If the greatest care isn't taken during the refit the differential side (driveshaft) oil seal can be damaged and I expect that is where the fluid is leaking from.

Jul 15, 2018 • Cars & Trucks

0helpful

1answer

How to replace front wheel bearing

pull wheel remove grease cap undo carter key remove nut pull off rest of hub take bearings frt and rear out of hub clean old grease from bearings check bearing for defect install in revers order remender to install new grease in new bearings lots of grease and u will need new seals for same front and rear

Jun 14, 2014 • 2006 Suzuki Verona

0helpful

1answer

Sound coming from Frt pass tire

Most likely a wheel bearing

Nov 20, 2013 • 2003 Pontiac Grand Am

0helpful

2answers

2000 malibu grinding noise, not brake squeal, during braking

frt wheel bearings make that noise, probably the problem replace both frt hubs and will more than likely take care of the problem

Dec 03, 2012 • 2000 Chevrolet Malibu

0helpful

1answer

CHANGE RT FRT WHEEL BEARING 1994 BUICK REGAL ...3.8.....FRT WHEEL DRIVE

You will have to remove the wheel,of course,remove the brake caliper,pads,and the brake caliper bracket,then the rotor,and any brackets holding the brake hose to get it out of the way.Then remove the large nut on the axle,and remove all the bolts holing the bearing assembly on the spindle,and tap it out ward,and make sure the axle stays put,do not let the axle come outward with the bearing,using a two by four to tap the axle inward toward the axle while removing the bearing assembly.If this was at all helpful,please rate,thank you.

Aug 20, 2010 • Buick Regal Cars & Trucks

0helpful

1answer

Loud roar from frt end when driving/frt v joints or wheel brgs ?

If the sound comes and goes while your starting and stoping driving it is a wheel bearing,
If you want to do this your self i can explain how to replace it,
you will need some tools/metric
a jack and jack stand
wheel bearing is about 75.00 and labor is about 1.5 hours if experienced and about 3 hours if not experienced
Thanks

Jul 15, 2010 • 2000 Dodge Caravan

3helpful

1answer

Rear wheel bearing replacement on 2003 escape

part is about 38 dollars ( frt wheel dr ) and must be pressed into the rear knuckle assembly.. if you dont have a press you can remove the rear knuckle and take it to shop to have it pressed out and in.

Apr 13, 2010 • 2003 Ford Escape

0helpful

1answer

Wheel bearings on 1988 chevy S-10

remove grease cap,brake caliper, then remove nut holding rotor now remove rotor, remove grease seal now both bearings should be out ,if replacing races then punch them out and tap new ones in, repack new bearings with grease install rear one and install new grease seal, slide rotor on slide frt bearing on, install washer and nut, tight a little to nearest cotterpin hole,put cotterpin in and put caliper on, hope this helps,good luck.

Oct 27, 2009 • 1988 Chevrolet S-10

2helpful

1answer

What is the torque spec for a frt wheel bearing half shaft nut for a 2003 chev impala

according to autowaresgroup.com the proper torque is 159 foot pounds

Oct 22, 2009 • 2003 Chevrolet Impala

12helpful

3answers

Between 0 and 20 mph there is a very loud grinding noise. there is also play in the steering at high speed, and when i go over bumps my front end feels loose. what could it be?

if growl is faster or slower with speed & changes with speed & turns its a wheel bearing also frt struts may bee weak check other frt end tie rods balls joints c-arm bushing all known to go bad

Aug 27, 2009 • 1997 Pontiac Grand Am

Question 2

Anonymous

Master 353 Answers
Posted on Sep 15, 2009

Anonymous

Master

Joined: Jul 25, 2009

Answers

353

Questions

2

Helped

351233

Points

1581

2003 Hummer H2 V8-6.0L VIN U
Wheel Bearing: Service and Repair
WHEEL HUB, BEARING, AND SEAL REPLACEMENT
REMOVAL PROCEDURE
NOTE: Never place vehicle on the ground with the halfshaft removed or the halfshaft nut torqued improperly. Otherwise, bearing seals may become
dislodged causing premature wear and/or damage to the hub and bearing assembly.
1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the tire and wheel.
3. Remove the rotor.
4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle.
5. Disconnect the electrical connection for the wheel speed sensor.
6. Remove the wheel driveshaft nut retaining cover.
7. Remove the wheel driveshaft assembly retaining nut and washer from the wheel driveshaft assembly.
Disengage the wheel driveshaft from the wheel hub and bearing.
8. Remove the wheel hub and bearing mounting bolts.
9. Remove the wheel hub and bearing and splash shield from the vehicle.
10. Remove the O-ring seal from the steering knuckle bore.
11. Remove the wheel speed sensor from the wheel hub and bearing.
12. Clean and inspect the O-ring seal.
13. Replace the seal it the following conditions exist:
- Nicks
- Cuts
- Dry or brittle
- Compression set
INSTALLATION PROCEDURE
1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
3. Install the O-ring to the steering knuckle.
NOTE: Refer to Fastener Notice in Service Precautions.
4. Install the wheel speed sensor to the wheel hub and bearing.
Tighten
Tighten the sensor mounting bolt to 18 N.m (13 lb ft).
5. Install the wheel hub and bearing and splash shield to the vehicle.
6. Install the wheel hub and bearing mounting bolts.
Tighten
Tighten the wheel hub to knuckle bolts to 180 N.m (133 lb ft).
7. Install the nut and washer retaining the wheel drive shaft assembly to the wheel hub and bearing.
Tighten
Tighten the nut to 210 N.m (155 lb ft).
8. Connect the electrical connection for the wheel speed sensor.
9. Install the wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle.
Tighten
Tighten the bolt to 12 N.m (106 lb in).
10. Install the rotor.
11. Install the tire and wheel.
12. Lower the vehicle.
frt. wheel bearings 2003 h-2 - 907ae15.jpg

Related Topics:

Trustworthy Expert Solutions

Frt. wheel bearings 2003 h-2

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Dealer replaced driver side frt wheel bearing. When I got home and looked under frt end there is a lot of fluid dripping off center casing car has never leaked adrop before what could have happened

How to replace front wheel bearing

Sound coming from Frt pass tire

2000 malibu grinding noise, not brake squeal, during braking

CHANGE RT FRT WHEEL BEARING 1994 BUICK REGAL ...3.8.....FRT WHEEL DRIVE

Loud roar from frt end when driving/frt v joints or wheel brgs ?

Rear wheel bearing replacement on 2003 escape

Wheel bearings on 1988 chevy S-10

What is the torque spec for a frt wheel bearing half shaft nut for a 2003 chev impala

Between 0 and 20 mph there is a very loud grinding noise. there is also play in the steering at high speed, and when i go over bumps my front end feels loose. what could it be?

Not finding what you are looking for?

2003 H2

Dealer replaced driver side frt wheel bearing. When I got home and looked under frt end there is a lot of fluid dripping off center casing car has never leaked adrop before what could have happened

Ask a Question

Check Out the Latest Top Trucks Report!

Top Hummer Experts

ZJ Limited

ROBERT GARCIA

Brad Brown

Are you a Hummer Expert? Answer questions, earn points and help others

Manuals & User Guides

. 2003 H2 Manual

Related Topics:

Trustworthy Expert Solutions

Frt. wheel bearings 2003 h-2

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Dealer replaced driver side frt wheel bearing. When I got home and looked under frt end there is a lot of fluid dripping off center casing car has never leaked adrop before what could have happened

How to replace front wheel bearing

Sound coming from Frt pass tire

2000 malibu grinding noise, not brake squeal, during braking

CHANGE RT FRT WHEEL BEARING 1994 BUICK REGAL ...3.8.....FRT WHEEL DRIVE

Loud roar from frt end when driving/frt v joints or wheel brgs ?

Rear wheel bearing replacement on 2003 escape

Wheel bearings on 1988 chevy S-10

What is the torque spec for a frt wheel bearing half shaft nut for a 2003 chev impala

Between 0 and 20 mph there is a very loud grinding noise. there is also play in the steering at high speed, and when i go over bumps my front end feels loose. what could it be?

Not finding what you are looking for?

2003 H2

Dealer replaced driver side frt wheel bearing. When I got home and looked under frt end there is a lot of fluid dripping off center casing car has never leaked adrop before what could have happened

Related Topics

Ask a Question

Popular Questions

My 2004 H2 Hummer rear hatch door is broken where

Hummer H2 will not start.

Where is the blend door actuator located on 03 Hummer h2. Driver side blows cold, passenger side blows hot

Keys stuck ignition of my H2

My dash board guages in my H2 don't come on

Check Out the Latest Top Trucks Report!

Top Hummer Experts

ZJ Limited

ROBERT GARCIA

Brad Brown

Are you a Hummer Expert? Answer questions, earn points and help others

Manuals & User Guides

. 2003 H2 Manual