My jeep renegade has a message service passive entry system how do I do that

it should be in your owners manual

copy and paste
https://www.dash-lights.com/jeep/renegade-dashboard-warning-lights/

NO FOBS DETECTED
Refer to Keyless Entry System Description and Operation

Keyless Entry System Description and Operation - Passive
Passive keyless entry allows entry to a locked vehicle without pressing any buttons on the keyless entry transmitter. You must only have the transmitter with you. This passive system is also part of the vehicle starting system. It allows you to start and run the vehicle having only the transmitter as your key. The passive entry and starting system use low frequency antennas in 4 different areas on the vehicle to determine the location of the transmitter. When passively opening a locked door or the rear compartment lid, you must have a programmed transmitter with you in your pocket, purse, or briefcase. As a customer opens the door handle or presses rear compartment touch pad, the low frequency antenna sends out a challenge to the keyless entry transmitter. The transmitter must be in a one meter range of the door or rear compartment lid in order to receive the challenge. If the challenge is met, the transmitter will respond, allowing the door to be unlocked and opened. Passive entry allows you to operate the following features:
• Passive door unlock/unlatch
• Passive rear compartment lid release
• Illuminated entry lamps
• Vehicle starting
The keyless entry system has the following components:
• Keyless entry transmitters
• LH and RH door antennas (part of the door handle assembly)
• Rear compartment antenna
• Console passive antenna
• Console active antenna
• Instrument Panel Module (IPM)
• Rear Integration Module (RIM)
• Remote Control Door Lock Receiver (RCDLR)
• External RF Antenna (includes coax from RCDLR to back glass)

Remote Control Door Lock Receiver (RCDLR)
The RCDLR is a multi-function module which controls all the vehicles antennas for passive keyless entry functions. The RCDLR also acts as the receiver for active keyless entry and tire pressure monitoring (TPM) functions, as well as controlling all immobilizer functions.
The RCDLR's RF antenna is located in the back glass, and there is a coax cable connecting the glass antenna to the module located in the trunk.

Your best bet , take it to a qualified repair shop that has the factory Tech 2 scan tool or someother professional type scanner that can read • Rear Integration Module (RIM) DTC'S - diagnostic trouble codes .

Pull out on the end of the headlamp switch.

The sensor should be mounted at the rear of the engine next to the distributor at block.

oxygen sensor?

Check with faxonautoliterature.com. They list a couple of wiring diagrams for 1984 Jeeps although they don't specify Renegade. These are official Jeep dealer diagrams for $29. I've used them before and had excellent service. Hope this helps.

check brake switch under brake pedal... if not working change it..

there are two buttons on the diagram panel screen, push and hold top button and a one of the entries will start to blink, then you use the bottom button to change the entry, when you are ready to move to the next entry push the top button again.

Alarm Module Reset Procedure
NOTE: This information applies to a Vehicle Theft Security System (VTSS) that was armed when the battery was disconnected and reconnected.
When the armed VTSS senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed following a battery reconnection.
The power-up mode will also apply if the battery goes dead while the system is armed and battery jump-starting is attempted. The engine no-run feature will prevent the engine from starting until the alarm system has been actively or passively disarmed.
Passive disarming of the Vehicle Theft Security System (VTSS) occurs when the vehicle is unlocked using the key to unlock either front door or the lift gate. Active disarming of the VTSS occurs when the vehicle is unlocked by depressing the Unlock button of the Remote Keyless Entry (RKE) transmitter.
Once the alarm has been activated (horn sounding, lights flashing, and the engine no-run feature), either disarming method will deactivate the alarm.
Depressing the Panic button (if equipped) on the RKE transmitter will also disarm the VTSS, but the horn will sound and the lights will flash for about three minutes as part of the Panic feature. The horn and lights can be stopped by pressing any of the RKE transmitter's buttons or driving the vehicle above 15 mph.

This totally depends on how Much "Hard Driving" that you do. Offroad, 4x4 all the Time, ETC.... If you do I would Change at every 50,000 If not Every 80,000 is OK