Question about Buick Enclave

Open Question

How do you remove the front power window switch on a 2012 buick enclave

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 110 Answers

SOURCE: HOW DO YOU CHANGE FRONT RIGHT HEADLIGHT ON A 2009 BUICK ENCLAVE

you must remove front bumper cover

Posted on May 10, 2010

Ad
  • 1425 Answers

SOURCE: How do I remove the front driver side power window switch on a 2008 Buick Enclave


Armrest Door Pull

Remove Rubber Cover

Remove 10mm *****
The first step is to pry out the plastic trim plate behind the chrome colored door release handle using a small flathead screwdriver.Then remove the 10mm ***** behind the plate using a ratcheting wrench with an extension bar attached.
Next pry out the rubber cover at the bottom of the door pull located in the center of the arm rest. Use a Torx T-25 (star bit) screwdriver to remove the two screws.
Remove Torx T25 Screws

2 T-25 Torx & 1 10mm *****

Pry Up Arm Rest Panel
Use a flathead screwdriver to pry up the rear of the plastic arm rest panel. There is a plastic hook at the front of the panel, so only pry it up from the rear edge.
Lift Rear End First

Plastic Hook At Front of Panel

Power Window Connector
After you lift out the arm rest panel, you'll need to disconnect the power connector for the window and door lock switches.
Push Connector Release Tab

Power Connector Unplugged

Two More T25 Screws
Push on the release tab with a flathead screwdriver and pull out the power window / door lock connector.Use a Torx T25 screwdriver to remove the two screws located below the arm rest panel.
Remove T25 Torx Screws

Outer Edge of Panel

Push In Center of Fastener
Then move to the outer edge of the door panel and locate the two small round fasteners. Use a small screwdriver to pop in the center pins of the two fasteners.
Pull Out Plastic Rivet

Black Plastic Fastener Removed

Remove Lower Fastener
Pull out the two plastic rivet fasteners and set them aside in a safe place.
Pull Panel Away From Door

White Plastic Pop Rivets

Pull Off Sail Panel
Grab the door pull in the arm rest and tug it towards yourself to disengage the pop rivet friction fasteners that hold the panel to the door frame.Move to the top corner of the door panel and pry off the triangular "sail" panel. On some vehicles, the sail panel contains the tweeter speaker.
Lift Panel Off Door Lock

Pull Out Door Pull Cable
Lift the door panel off the door lock button and tilt the top of it out towards yourself.Use a pair of needle nose pliers to gently lift the metal ball at the end of the door opener cable out of the mechanism.
Disconnect the door cable from the back side of the door panel.
Door Pull Cable Removed

Disconnect Power Mirror
Then disconnect the power connector for the side view mirror by lifting up on the release tab. Slide the power connector off the plastic anchor on the metal door frame.
Slide Connector Off Anchor

Unlock Connector

Connector Detached
Look behind the door panel and locate the large wire connector with the pink lever lock. Swing the lever open to unlock the connector and separate it from the socket.


Door Panel Removed

Power Window Motor

10mm Bolts
Now the door panel can be completely removed by lifting it up and off the door frame.To replace the power window motor, remove the 10mm bolts.
Stock OEM Door Speaker

Remove 7mm *****
The stock "OEM" speaker is held in place by a single 7 mm *****. Remove it with a socket and ratcheting wrench.
Pry Off OEM Speaker

Speaker Removed

Disconnect Power Plug
If the speaker is stuck to the door frame, gently pry it off with a small flathead screwdriver.Disconnect the speaker's power plug by pressing the release tab with the small flathead screwdriver.
Fits 5.25", 6.5", 6.75"

Re-installing Door Panel
According to the Crutchfield website, the 2008 to 2012 Chevrolet Malibu's front door speakers can be replaced withaftermarket speakers in the following sizes: 5 1/4", 6 1/2" or 6 3/4" speakers with the use of a bracket.If you'd like to reduce road noise, make your car quieter and also improve the sound from your speakers, I'd recommend applying some Dynamat Sound Deadener on to the metal door frame.
Re-Attach To Anchor

Plug In Power Side View Mirror

Re-Insert Power Connector
To re-install the door panel, first hold the panel close to the door frame before re-connecting the large wire plug. Swing the pink lever closed to lock it in place.Slide the socket for the power side view mirror back on to its anchor and insert the power plug.
Lock Power Connector

Pink Lever Locked

Re-Insert Door Pull Cable Ball
Insert the metal ball at the end of the door opener cable back in to the door handle mechanism.Slide the black plastic cone part of the cable back into the slot in the door opener assembly.
Door Opener Cable Reinstalled

Hang Door Panel On Frame
Gently lower the door panel down on to the edge of the door frame with the door lock switch through the opening at the top.
Line Up White Plastic Fasteners

Push On Sail Panel

Push Door Panel In Place
Move to the bottom of the door panel and line up the white plastic pop rivet fasteners with the holes in the metal door frame.Push all around the door panel to re-insert the pop rivet fasteners.
Re-attach the sail panel at the top corner of the door frame.
Push Panel Flush Against Frame

Insert Side Edge Fasteners

Insert Larger Piece First
Next move to the side edge of the door panel and first re-insert the larger piece of the two fasteners. Then insert the smaller "pin" piece of the fastener into the middle of the larger piece.
Insert Small "Pin" Piece

Install Lower Edge Fastener

Tighten 2 T25 Torx Screws

Re-Attach Power Connector

Insert Front Hook First
Insert and tighten the two Torx T-25 screws located under the arm rest.Re-attach the power connector to the plastic arm rest panel.
First insert the hook at the front of the arm rest panel and then snap the rear end in place.
Pop Arm Rest Panel In Place

Tighten 2 T25 Screws

Replace Rubber Cover
Insert and tighten the two T25 Torx screws into the door pull cup. Then replace the rubber cover over the two screws.
Tighten 10mm Door Handle *****

Replace Door Handle Trim Plate

Malibu Door Panel Replaced
Replace the 10mm ***** that goes above and behind the door opener handle and tighten it. Pop in the plastic trim plate behind the door handle.

Posted on Apr 10, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Window fogs after I have been driving for a while on my 2012 buick enclave try different settings nothing helps


Try turning on the A/C until the fog clears. Because you say that the problem occurs after you have been driving for awhile, there may be a problem with the system.

Oct 15, 2018 | Buick Cars & Trucks

1 Answer

Car will not start


Buick Enclave No Start Problems - Car Forums at Edmunds.com

forums.edmunds.com > Buick > Buick Enclave

Mar 1, 2009 - 31 posts - ā€Ž13 authors
Learn more about Buick Enclave at the Edmunds.com Car Forums! Read real ... Time to take it in and see why car will not start with the remote key. Anyone else .... I drove my brand new 2011 Enclave yesterday. It sat for an ... Buick Enclave engine won't shut off. Parking brake light ...
5 posts
Aug 9, 2014
Buick La Crosse Stalling/Starting Problems
31 posts
Jul 26, 2006
More results from forums.edmunds.com

EnclaveForum.net: Won't start from time to time

www.enclaveforum.net > ... > Recalls, TSBs, FAQs, Links & How To's

Jun 23, 2008 - 20 posts - ā€Ž16 authors
I have been having an issue of my Enclave not starting from time to time. If I turn the ignition back off and try again, sometimes it will start after the first ... 2011 Audi Q7; 2009 Audi A8L ... I usually just "flick" the key to let it auto-start and it normally works fine but ..... BUICK ENCLAVE Technical Service Bulletin EnclaveForum.net: 2013 BUICK ENCLAVE ...
20 posts
Aug 14, 2014
EnclaveForum.net: Car continues to run after key removed
20 posts
Nov 13, 2012
EnclaveForum.net: evaporation hose on gas tank - does ...
17 posts
Jun 25, 2012
EnclaveForum.net: Engine won't start low fuel level
12 posts
Feb 3, 2012
More results from www.enclaveforum.net

Jan 05, 2016 | 2011 Buick Enclave

1 Answer

Buick Enclave will occasionally at a stop rev up to between 2000-4000 rpm


Three possible reasons for this are
1. You have a vacuum leak
2. The throttle position sensor (TPS) has gone bad
3. The idle air control valve is bad or blocked up.

May 01, 2014 | 2012 Buick Enclave Base 4dr SUV 3.6L V6...

1 Answer

Checking the fuse on a buick enclave


On this website (link below) you finde fuse box diagram and description for Buick Enclave 2011

BUICK Enclave 2011 2012 fuse box diagram Auto Genius

Dec 24, 2013 | 2011 Buick Enclave

1 Answer

12 volt outlet buick enclave fuse


On this website (link below) you find fuse box diagram and description for Buick Enclave 2011

BUICK Enclave 2011 2012 fuse box diagram Auto Genius

Jan 28, 2013 | 2011 Buick Enclave

2 Answers

Where is the battery on the 2011 enclave


check under the back seat. the back seat can be removed by pulling up on the front of the seat.

Iā€™m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jul 07, 2011 | 2011 Buick Enclave

4 Answers

Where is the battery in a 2008 buick enclave?


it may be under the back seat,,buick notorious with that..

Jan 20, 2011 | 2008 Buick Enclave

2 Answers

Cant find oil filter location on 2010 Buick Enclave


As auto consumers we should all know by now that the auto industry does not want you to do self-maintenance - they want the service revenues.
If you want to locate the oil filter in 2012 Buick Enclaves, it's located between the
radiator and the engine block (Surprise!). Furthermore it's replaced from the top of
the engine compartment (Another surprise!) -- Good luck

Jul 02, 2010 | 2008 Buick Enclave

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...