I have a question. I see the videos and seeing the step by step process of replacing the front brake pads of a Honda Sabre 1100 VT C2. At no point does it ever state to pull off the cap to the master cylinder. How are you compressing the caliper piston without creating room in the system for the hydraulic fluid to go somewhere?

Take the wheels off and look at the calipers. If there is 1/8 of an inch or less of pad, it is time to replace the pads.

For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

will try to help. 1st remove the wheel, then remove the 2 caliper bolts that hold the brake caliper on. after removal of brake caliper, [it should just pull off after the 2 bolts are removed] replace the brake pads[be sure to apply anti squeal lube to the outer side of the pads..not the pad itself,the one not contacting the brake rotor] install the pads, the you will need a C clamp to push the brake caliper pistons back into the caliper. i've used this installation easily. use the old pad ,place it against the caliper piston,then apply the C clamp and push the caliper piston back into the brake caliper, then the brake caliper will slide back over the new pads easily, no need to bleed the brakes if you use this solution. replace the brake caliper bolts, then go to next side and repeat the process. after the replacement of the front brake pads,pump the brakes with engine running!!! it's really a simple process. be sure the brake pads are facing the brake rotors with the [pads] facicing the rotors. no metal facing metal. easy! if you have added brake fluid recently, do not be alarmed if you see fluid coming out of the brake master cylinder,when you use the C clamp to collaspe the brake caliper back into the recessed position. [as always when you have to add brake fluid to the brake master cylinder,it only means your brakes are wearing naturally. if you have a vibration in front wheels or steering wheel when braking, you have a brake rotor or both front brake rotors that need replacement with your brakes also. hope this helps and as always, please get a second opinion if you have doubt. an expert will be happy to help. thank you for choosing fixya.com

Front brake
Step 1: Identify Front Disc Brake Components

Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads

Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper

Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads

Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount

Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor

Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper

Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor

Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads

Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper

Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Front brakes on all modern cars are disc brakes. The front brakes generally provide 80% of the stopping power, and so tend to wear faster than the rear. Replacing them - pads, rotors and calipers - is quite simple once you understand the process, and can save you a great deal of money. These instructions will include a full front brake replacement. Also, having a service manual for your vehicle will save your sanity, as well as time and money. If you only need pads, or pads and rotors, but not calipers, skip the steps for replacing calipers. Repeat the steps below for each side of the car as necessary.
Complete Directions

jack up front, remover tire, remove bolts on backside of caliper, slide caliper off bracket, remove old pads (paying attention to how they fit in), remove cap on master cylinder under hood, use a caliper tool to push the piton back in, replace pads, put it all back together again....

good luck -- we are here if u need furhter help

Are you talking about the car brake pads? Front wheel brake pads are usually easy to change as compared to the rear. You'll have to remove the front wheel to proceed. If this is your first time replacing brake pads, I suggest you take it to the mechanic or watch the video series below to get an idea. Good luck!
http://www.youtube.com/watch?v=xOkbcAdw0Es

I’m assuming you got either the factory original ceramic brake pads or at least a decent quality aftermarket ceramic brake pad, not some cheapo semi metallic brake pad, such as Duralast or Raybestos PG’s.

When you replaced them did you properly lube the metal to metal contact points on the calipers? Remember, the pads have to be free floating, otherwise they will not properly engage and disengage from the rotors.

Did possibly some of the caliper lube get on the friction part of the brake pads? Whoops, no friction then. It happens, solution is buy another set, sorry.
Did you bleed all four brakes? Even though the system was not “Opened”, guess what, it already was every time you touch your brakes. The extreme heating and cooling during normal brake operations, even more so on Antilock Braking Systems (ABS ), sucks in moisture through those rubber brake lines and various other connection points. That’s the first reason why you do a quick bleed of the system. The second is to balance out the four wheel braking abilities, if you don’t, as the front wheels start to slow faster then rear, the ABS system releases the front brakes to maintain control.

autozone.com has the best available information that is at no charge. They give you step by step instrucions and pictures with exploded views. Once you do the brakes a time or two it will be a snap. At the site simply add your vehicle and go to vehicle repair guides. Hope this helps.

Maybe this is a multiple post. The best available no charge is autozone. com When you go to the site, input your vehicle information and go to vehicle repair guides. They have step by step instructions and exploded views. Once you do the brakes a time or two it will be a snap. Hope this helps.