Question about Mazda Cars & Trucks

1 Answer

I HAVE A MAZDA ETUDE 1.6 ZM ENGINE WITH NO SPARK

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 85,160 Answers

What year and what codes are showing up in a test.

Posted on Aug 15, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Mazda Etude 160ie timing

I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Posted on Nov 27, 2010

astrawoid
  • 294 Answers

SOURCE: my mazda etude is having

Remove that plug and turn engine over. Does water shoot out of the spark plug hole? Head gasket leak, cylinder-to-coolant channel side. Do you see any water vapor or actual water out of your exhaust when you first start it?

Posted on Nov 28, 2010

  • 31 Answers

SOURCE: hello, we're in need of a

i hope this helps
tar171_1.gif
tar171_0.jpg

Posted on Dec 24, 2010

  • 172 Answers

SOURCE: When the tension er come

Is this the fan (serpentine accessory) belt, or the cam belt? the fan belt drives the alternator, air conditioner, etc, and is visible on the front of the engine. The cam belt is usually behind a cover of some kind and can't be seen.
If it is the fan belt, no damage. If it is the cam belt, it depends on the engine design. maybe no damage, maybe serious damage to the valves. If you replaced the tensioner and properly aligned the cam and crank pulleys, and it won't start, you most likely have serious damage to the valves. You will need to pull the head, have the damaged valves replaced, after inspecting the pistons for damage.

Posted on Jan 28, 2011

  • 575 Answers

SOURCE: need timing belt marks diagram for mazda 323 160i , 2001 model, zm engine

11_30_2012_7_10_14_am.jpg
I would have liked to add as an attachment but could not.

Posted on Nov 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have no spark on Mazda etude 1.6


reasons for no spark
cam crank position sensor failure
broken timing belt/chain
immobilizer activated
failure of the ignition control module
run the fault codes to find which has happened.

Sep 19, 2015 | Mazda Cars & Trucks

1 Answer

Mazda etude 1.8 no spark


If you do not have any spark ( petrol engine ) check for distributor cap, rotor arm, ignition module inside the electronic distributor, or any loose wiring connected on distributor or ignition coil or any wire.Also check and the HT Leads.

Jul 02, 2014 | 2003 Mazda 323

1 Answer

Mazda etude familia not producing spark to the engine while the distributor has a spark


The rotor under the distributor may be bad, pulled the cap and turn the engine over look at the rotor and make sure its turning. If it doesn't turn the distributor gear maybe sheared, timing belt or timing chain may have come off.

Dec 18, 2013 | 2003 Mazda MPV

1 Answer

Hi i got a mazda etude 1.6 2001 model with the Zm engine firstly does it have hydrolic valve and why if the car idle it backfire and miss if i drive the car is very sluggage do you think my plugs it done...


i would start by changing the fuel filter and air filter. if the check engin light is on read the codes at a parts store for free to see why its on

Mar 14, 2013 | Cars & Trucks

1 Answer

Mazda etude immobiliser problems


i lost my mazda etude immobiliser,when i try to cancell it,the engine only run for few seconds and stop.when i check the coils they are boilling i run out of ideas.

Feb 25, 2013 | Cars & Trucks

1 Answer

Mazda etude 1.6 i cut out while driving starting after about 10 min.


sounds like the coil pack is braking down when hot. check for spark while engine wont start

Nov 16, 2011 | 2003 Mazda MPV

1 Answer

My mazda etude is having water in one of the spark plugs


Remove that plug and turn engine over. Does water shoot out of the spark plug hole? Head gasket leak, cylinder-to-coolant channel side. Do you see any water vapor or actual water out of your exhaust when you first start it?

Nov 28, 2010 | 1997 Mazda Protege

1 Answer

Timing belt setting and my car iddle are out of form mazda etude


Your camshaft and crankshaft pulleys have to be properly aligned upon installation of the timing belt. The cogs on the belt, should fit precisely with the teeth of the pulleys. Your # 1 engine cylinder should be moved to "Top Dead Center" before installing the belt. This means no compression once the top of the piston cylinder reaches the top of the chamber.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_62314e5b2470e8b5

Nov 27, 2008 | 2002 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...