Question about Cadillac Cars & Trucks
In a 2014 Cadillac ATS
No its a one piece unit
Posted on Aug 14, 2019
Even if you could, the replacement unit isn't that expensive and takes less time. Time is money.
Posted on Aug 14, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
It is pretty easy, there is not much labor involved if it has anti-lock brakes in the rear you will also have to un-plug the wire harness attached to hubs.
Posted on Nov 26, 2008
it is best to replace the whole compressor but if it was me I would go and get a can of 134A oil and put that in first to see that helps with the problem and if not then replace the compressor they are somewhere around $40 to $75 at a good salvage yard and you can try www.junkyarddog.com and if you cannot find one there try www.schramauto.com or call them at 1-800-292-1032
Posted on Mar 22, 2009
The wheel bearings on these vehicles are not adjustable. If the bearings become loose or make noise, they must be replaced.
Removal & Installation
NOTE Lay the hub and bearing on the wheel studs on the outboard side. This will avoid damaging the bearing seal.
Tire and wheel Caliper, leaving the fluid lines connected Brake rotor Halfshaft from the hub and bearing on 4WD vehicles. Place a brass drift against the outer edge of the halfshaft to protect the shaft threads. Use a hammer to sharply strike the brass drift, but to do not remove the halfshaft at this time. Wheel speed sensor Wheel hub and bearing-to-steering knuckle bolts and hub and bearing
Splash shield from the steering knuckle Seal from the hub and bearing
Wheel hub and bearing seal Splash shield to the steering knuckle, making sure it-s properly aligned Hub and bearing to the steering knuckle, aligning the threaded holes Hub and bearing bolts and tighten to 77 ft. lbs. (105 Nm) Wheel speed sensor. Tighten the bolt to 13 ft. lbs. (18 Nm). Rotor and brake caliper Tire and wheel
The Hub Bearing Torque - Front
If Torque Specs are not in the box we recommend youtorque to this setting. Axle Nut: 103 Ft/Lbs.Flange Bolts: 77 Ft/Lbs. WARNING: Failure to observe the following warningscould create a risk of death or serious injury.Proper maintenance and handling practices arecritical.Always follow installation instructions and maintainproper lubrication.Every reasonable effort has been made to ensure theaccuracy of the information contained in thiswriting, but no liability is accepted for errors,omissions or for any other reason.This information is not intended to substitute forthe specific recommendations of your vehiclemanufacturer.Always use the recommended torque requirement unlessotherwise specified in the carton.Depending on the application, type of hub unitbearing and location, the installation process mayvary.Please review the vehicle manufacturer'srecommendation before removing or installingcomponents.
Posted on Nov 10, 2012
Tips for a great answer:
Aug 18, 2018 | Cadillac Cars & Trucks
Dec 09, 2015 | Kia Cars & Trucks
Nov 26, 2015 | Toyota Cars & Trucks
Dec 15, 2014 | 2014 Cadillac ATS
Dec 04, 2012 | 1996 Cadillac DeVille
Oct 23, 2010 | 2005 Mazda 3
Aug 27, 2010 | 1994 Chrysler LHS
Jul 04, 2010 | Mercury Mountaineer Cars & Trucks
Jul 03, 2010 | 1996 Cadillac DeVille
15 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: