1999 GMC safari AWD mini van hub /bearing

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

2000 GMC Safari AWD Suddenly won't start - Fixya

www.fixya.com/cars/t1464758-2000_gmc_safari_awd_suddenly_start
Dec 31, 2008 - 2000 GMC Safari AWD Suddenly won't start 2000 GMC Safari AWD, I have never had one problem with this van till now It - GMC 2000 Safari .

Three bolts are 70 lbs,could be 120+/-.

I just re-packed the front end bearings. Haynes covers the brakes real well, but not the bearings. Each front wheel has two bearings (one inside the wheel). So you have to remove the wheels, brakes, dust cap, grease seal and brake rotor to access the bearings. .
Expect to replace the grease seal because the rubber will be brittle or hard. Clean and inspect the bearings and races real well. If the bearings are squealing expect to replace some of them also.
Replacing the brakes so the pads stay in place is the trickiest part.

1999 GMC Safari Van AWD 4.3 liter V-6 VIN "W"




Hope helps (remember to rate this).

Yes you do have to pull the axle and make sure you put everything back in the same place you removed it from. The ring and pinion shouldn't have to be bothered. You will have to remove the rear end cover to remove the axle. Its very easy to do. There is a pin inside the rear end that has to be removed to pull the axle. Pay attention to how you take it out and put it back the same way. It sounds as if you can do this with no problem.

LOCATION OF BLOWER MOTOR IS UNDERHOOD ON PASSENGER SIDE NEAR WINDSHIELD. RESISTOR IS LOCATED IN THIS GENERAL VICINITY ALSO. THE RESISTOR WILL STICK DOWN IN THE EVAPORATOR CASE AND HAS SEVERAL WIRES COMING OUT OF IT. THE CONNECTOR BODY IS BLACK OR GREY. HOPE THIS HELPED YOU!

Give it a good hard hammer with a 5 pound hammer. If your planing to use it again, use and plastic hammer or put wood against the Rotor where your going to Hit it.
The rotor is held on by rust to the hub assembly. 
Good luck and wear ear plugs, kinda hurts the ears. LOL

takr the belt off and turn the alt by hand you can tell if the bearings are going out it should turn freely and smoth

This rear end needs to be replace or re-built


































This rear end needs to be replaced or re-built. The gears and or bearings are worn/shot. May be able to get a complete rear end from a Junk yard for much less, one in good condition. Good Luck