2001 Lexus RX 300 Logo

Related Topics:

Posted on Sep 10, 2009

O2 sensor lexus rx300 what colour wires do what?

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

Hot-Shot:

An expert who has answered 20 questions.

  • Contributor 40 Answers
  • Posted on Sep 17, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

Hot-Shot:

An expert who has answered 20 questions.

Joined: Sep 15, 2008
Answers
40
Questions
0
Helped
51865
Points
69

One usually heats the sensor (power) the other is a ground and they other sends the ohms of resistance to the computer, measuring exhaust air density, adjusting the fuel and ignition while you drive.

5 Related Answers

Anonymous

  • 5158 Answers
  • Posted on Apr 15, 2009

SOURCE: How many O2 sensors on a 1997 Lexus ES 300?

according to the manual i have... it has three.... one in the exhaust manifold.... and two in the exhaust pipe..... slightly vauge on the exact location of the last two sensors... but looks like it is after the catylitic converter.

Ad
Molson02536

Harvey N Tawatao

  • 3854 Answers
  • Posted on Jun 26, 2009

SOURCE: code p1130. where is the sensor located

P1130 Air/Fuel Ratio Sensor Circuit Range/Performance Malfunction (Bank 1 Sensor 1) 
This sensor is the hardest to get at. It is between the cat and the cylinder block on the bank of cylinders closest to the firewall. Not much wiggle room back there.
Sensor will run you about $225 from Toyota, $275 from Lexus, but you may be able to get a Denso sensor on line.

Good luck and hope this helps. keep me posted. 

Anonymous

  • 410 Answers
  • Posted on Jul 08, 2009

SOURCE: ? to Replace Timing belt on 2000 Lexus Rx300 with 57,000 miles.

If it is running perfectly I wouldn't think that you would need to replace the timing belt. You shouldn't need to replace that until 100,000-120,000 miles. I would definitely hold off until now unless you have start having some timing problems. Let me know if you have any other questions. Thanks for rating my response and for using FixYa!

Anonymous

  • 17 Answers
  • Posted on Aug 18, 2009

SOURCE: replace side marker light on lexus rx300

Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Anonymous

  • 185 Answers
  • Posted on Oct 09, 2009

SOURCE: where coolant temp sensor location for lexus rx300

coolant temp sensor is located on the bootom backside of the radiator. you will have to remove the front under cover to access it.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2000 Lexus RX 300. Where is the Engine Coolant Temperature Sensor located on my 2000 RX300 please?

Question edited for clarity, add maker.
Question moved to model category.

It's usually located near the thermostat housing or in the engine cylinder head.
Dec 17, 2020

Lexus RX300 Engine Coolant Temperature Sensor ...


0helpful
1answer

Where exactly is BANK 2 Sensor 1 located on a RX300 Lexus? everything I come across is for bank 1 sensors. A picture would help that is not from a google search because those are wrong.

https://www.google.com/search?q=lexus+rx300+bank+2+sensor+1&rlz=1CDGOYI_enUS765US765&oq=rx300+lexus+bank&aqs=chrome.2.69i57j0l3.14511j0j4&hl=en-US&sourceid=chrome-mobile&ie=UTF-8#imgrc=OXFmgnSkyDPiZM: The diagram says it is obscured.
0helpful
1answer

Driver side suspension drops when turned off works ok with engine running new sensor fitted still has problem

RX300 Mega Thread. Start here if you have a problem - Club Lexus ...

www.clublexus.com/.../679100-rx300-mega-thread-start-here-if-you-ha...
Feb 17, 2013 - One question per post please. ... manual-search, just enter RX300 or whatever Lexus vehicle and year ... Side affects of CEL: Based on the error code, your RX may end up in a .... You may hear a drop in rpm of the donor car. Window Switch Problems Pass side
Jul 17, 2015
RX300 knock sensor replacement DIY
Jul 6, 2015
RX300 (year 2004) air suspension fault
0helpful
1answer

What does code system to lean bank 1 mean on my 2000 lexus rx300

It could be caused by many things, but generally it means that your engine is running too lean - usually indicating a vacuum leak. It could also be that the O2 sensor is bad and giving a false reading.
5helpful
2answers

The engine light and VSC light are on (Vehicle Singapore 2004 Lexus RX 300. Diagnostics report Error code P0037

your o2 sensor is bad. vsc will go on for any small DTC displayed on the MIL (cel)

P0037 LEXUS P0037 LEXUS - Oxygen Sensor Heater Control Circuit Low Bank 1 Sensor 2 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
Possible causes - Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM) When is the code detected? The P0037 is set when the ECM detects an excessively low voltage through the heated oxygen sensor heater circuit P0037 LEXUS Description Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECMcontrols the heater element circuit by allowing current flow to ground.

The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.

o2_heater_circuit.gif
0helpful
1answer

1999 lexus rx300 4wd eng. light comes on, no power, rough idle hesitation cat converter cherry red. when computer reset runs ok for short time

Converter is ruined, as are the O2 Sensors

Now you have to fine out why

Rich Condition or Overheating,
Engine Misfires

Have fun !!
0helpful
1answer

2003 rx300 - problem the skid control light came

Most likely a bad wheel speed sensor or wiring harness issue.
0helpful
1answer

My lexus rx300 had the engine and vsc light on also.

The ck engine light is not triggered by just the o2 sensor. Is this a new vehicle? 5 or 6 times for the same problem and unseccessful? Hmmmm I belive the lemon law says the dealer has 3 attempts to correct the problem and of course federal emmision standards are more than likely not in compliance. Want another lexus?
Not finding what you are looking for?

469 views

Ask a Question

Usually answered in minutes!

Top Lexus Experts

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...