How to install a quarter window glass on a 2000 ford expedition

REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab

side panel.

(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

adjust the latch base or lock assembly

I would check the gauge ,sounds like it isn;t working right

Auto glass can be very difficult to try to fix. My step-dad used to be a mechanic, and he would mess things up every time he tried to fix anything related to the windows. Talking to somebody who specifically fixes windows will make life significantly easier. I would definitely suggest finding a glass repair company to help you out with these types of problems. http://glassunlimitedme.com/Window-Glass-Auto-Glass-Wells-ME.html

SOUNDS LIKE YOUR FUEL PUMP PICK UP TUBE HAS A PIN HOLE IN ITWHICH IS CAUSING IT TO SUCK AIR. MAY HAVE TO REPLACE FUEL PUMP.

Hello! #1: Your lower windshield is leaking, where you can't see it...and chances are, it is near the lower right corner...dripping onto/into your PCM . Take your Expedition to a glass-shop, and ask them to remove and reinstall your windshield.. Explain to them, you believe a water-leak to be hitting your computer. Properly re-installed, it should fix your drip-problem...

#2: Check under your dash, or have a body-shop check...chances are, that a piece of molding under the hood, by the wiper valence, is not installed properly, cracked or missing... If water drips by it, the only path is directly into the PCM...Guru..saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

I recently replaced the quarter window on my 2000 Lincoln I had to take apart the inside plastics there about 16 nuts around the inside window you might have to take of the seatbelts be sure to be careful you also might have to buy a type of window adhesive. When you take it off there is two plates that hold the window down you might have to pull them out a little to get them on the new window after that just reverse the process be sure to have a helper.

tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.

1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.

3-Door, 5-Door

1. CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
   NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
   NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
   Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
   1. 20 mm
   1. 60 mm
   1. 75 mm
   1. 90 mm

Wagon

1. CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
   NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
   NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
   Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
   1. 20 mm
   1. 30 mm
   1. 50 mm
   1. 40 mm

4-Door

1. CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
   NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
   NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
   Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
   1. 20 mm
   1. 25 mm
   1. 45 mm
   1. 50 mm
   1. 55 mm
   1. 70 mm
   1. 150 mm

All vehicles

1. Remove the rear quarter window glass.

1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.

Installation
CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.

1. NOTE: Avoid scratching the pinch weld.
   Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.

1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.

1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.

1. Clean the rear quarter window glass with a non-alcohol based window cleaner.

1. CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
   If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.

1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.

1. Cut the urethane adhesive applicator tip to specification.

1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.

1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.

1. Install the rear quarter window glass.

1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.

1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

this black holders are part of glass and glass should be replaced

antenna is probably in rear glass or rear side glass. Check for microgap and repair with rear window defoster repair kit. use a magnifying glass to find microcrack.