My2001 chrysler sebring dashboard instruments lights not working what could it be?

SOURCE: Here are the fuses for

my Sebring came with a 36 month Warrenty, does this cover it? If so take it back

SOURCE: I HAVE A 2005 CHRYSLER SEBRING AND DOME LIGHT,RADIO ALL POWER LOCKS HAVE QUIT WORKING

me too! - looking at fuse #5 red 10 Amp one but has black thing on it.

Can't get if off..

Have read the manual is wrong and to use panel on side of fuse box for fuse locations...

Greg Bernett

• 2993 Answers
• Posted on Jun 26, 2009

SOURCE: I need to replace an ignition switch on my 1999

This is for the ignition switch like you are asking for:

Ignition Switch REMOVAL & INSTALLATION Cirrus, Stratus, Sebring Convertible and Breeze CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the steering column. Failure to do so may cause accidental deployment of the air bags, resulting in unnecessary SIR system repairs and/or personal injury.

1. Disarm the air bag system, as described in Section 6.
2. Remove the left end instrument panel cover/fuse panel and remove the retaining screw holding the end of the instrument panel top cover.
3. Remove the instrument panel center bezel.
4. Remove the screws that secure the instrument panel top cover to the center of the instrument panel.
5. Lift the instrument panel top cover enough to gain access to the knee bolster attaching screws.
6. Remove the lower knee bolster attaching screws and knee bolster from the vehicle.
7. Remove the lower steering column cover attaching screws. Pull down on the lower cover to clear the ignition key cylinder and key release (if equipped).
8. Remove the lower steering column cover, sliding the cover forward while holding down the steering wheel tilt lever.
9. Tilt the steering wheel down to the fully lowered position and remove the upper steering column cover.
10. Remove the screws that hold the combination switch to the ignition lock housing.
11. Place the ignition lock cylinder in the RUN position.
12. Insert a small prying tool into the hole in the lower cover and depress the cylinder release tab.
13. Remove the ignition lock cylinder from the steering column.
14. Unfasten the electrical connectors from the switch.
15. Using a No. 10 Torx® bit, remove the ignition switch mounting screw.
16. Depress the retaining tabs and remove the switch. To install:
    
17. Place the ignition switch in the RUN position. Be sure the actuator shaft in the lock housing is also in the RUN position.
18. Install the switch, making sure the switch snaps over the retaining tabs.
19. Install the retaining screw.
20. Connect the wiring to the ignition switch.
21. Install the ignition lock cylinder.
22. Install the 2 combination switch mounting screws.
23. Install the lower and upper shrouds.
24. Install the knee bolster to the lower dashboard panel and tighten the lower knee bolster attaching screws.
25. Install the screws that secure the instrument panel top cover to the center of the instrument panel.
26. Install the instrument panel center bezel.
27. Install and tighten the screw holding the end of the instrument panel top cover. Install the left side instrument panel/fuse panel cover.

SOURCE: diagnostic Troubleshooting Codes for 1996 Chrysler Sebring Cvtble

FIRST YOU TURN IGNITION SWITCH ON WITH ENGINE OFF.LOOK AT MIL LIGHT IT SHOULD COME ON 3 SECONDS THEN GO OFF IT NOT THEN YOU GOT BURN OUT BULB OR A CIRCUIT PROBLEM.IF ALL IS WELL. ATTEMPT TO START ENGINE.TURN OFF IGNITION. WITH OUT STARTING ENGINE.TURN IGNITION ON OFF ON OFF AND WITHIN 5 SECONDS RECORD 2 DIGIT DIAGNOSTIC TROUBLE CODES.DISPLAYED BY FLASHING MIL LIGHT.YOUR MIL FLASHES WILL BE YOUR CODE LIKE THE MIL LIGHT FLASHES 5 TIMES THEN PAUSE FLASHES 3 TIMES THAT CODE 53 THAT YOUR CODE.IT LIKE MORSE CODE.WHEN DONE TURN OFF IGNITION SWITCH.GO TO AUTO ZONE OR ADVANCE AUTO GET HAYNES COMPUTER CODE BOOK. TO GET CODE MEANING OR WHAT SENSOR GONE BAD.HOPE THIS CAN BE SOME HELP.

SOURCE: instrument cluster bulb is out. how do i replace

It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.